Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › 2015.06–2018.06
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260591 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 17341K 5.REMOVE INTERCOOLER AIR HOSE

Hide 16571C 7.REMOVE NO. 1 RADIATOR HOSE

Hide 16470 8.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 82123 9.DISCONNECT NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

Hide 16620 11.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 23273C 12.REMOVE NO. 2 FUEL HOSE

a.

Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


Hide 23271H 13.REMOVE NO. 1 FUEL HOSE

A353389

a.

Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


Hide 22803 14.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A353390

a.

Remove the fuel injection pump cover subassembly from the supply pump assembly.


Hide 15.REMOVE FUEL PUMP MOTOR WIRE

A353391

a.

Disconnect the fuel pump motor wire connector.


b.

Detach the clamp and remove the fuel pump motor wire.


Hide 11324 16.REMOVE TIMING CHAIN COVER PLATE

A344936

a.

Remove the 3 bolts and timing chain cover plate.


b.

Remove the gasket.


Hide 22100 17.REMOVE SUPPLY PUMP ASSEMBLY

A354097

NOTICE:
·

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.
A353392E02
1.604,1.177 1.396,1.573 1.396,1.573 1.698,1.177 true 1.281,1.573 1.552,1.865 0.271,0.292 12 true *a

Align the timing mark of the crankshaft pulley subassembly and timing chain cover by rotating the crankshaft clockwise.

Text in Illustration
*a Timing Mark


b.
A344937E02
1.719,1.917 1.344,1.917 false 0.854,1.729 0.625,1.323 0.625,1.323 1.396,1.74 true 1.74,1.833 1.958,2.021 0.219,0.188 10 false *a 0.25,1.229 0.615,1.427 0.365,0.198 10 true SST

Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.

Text in Illustration
*a Hold
V100135

Turn

SST
09213-58014  (91551-80840)
09330-00021  

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



c.
A353387

Loosen the 3 nuts from the supply pump assembly.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



d.

Install SST with 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Install SST with the bolts included with SST.


HINT:
·
A454662E01
2.115,3.677 2.833,4.104 2.833,4.104 3.021,4.104 false 0.167,0.167 1.115,0.688 0.948,0.521 10 false *a 0.198,2.417 1.146,2.938 0.948,0.521 10 false *b 3.052,4 3.313,4.26 0.26,0.26 10 false *c


·

Make sure that the installation direction of SST is as shown in the illustration.

·

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.

Text in Illustration
*a Engine Front Side
*b Engine Rear Side
*c SST Hexagonal Portion




e.
A344941

Remove the 2 bolts and No. 1 fuel pump bracket from the supply pump assembly and cylinder block sub-assembly.


f.
A344939E02
2.063,1.771 1.74,1.771 false 1.281,1.521 1.156,1.073 1.156,1.073 1.76,1.583 true 2.438,0.75 2.76,0.75 true 2.063,1.698 2.302,1.896 0.24,0.198 10 false *a 2.802,0.656 3.208,0.885 0.406,0.229 10 true SST 0.781,0.99 1.135,1.177 0.354,0.188 10 true SST

Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.

SST
09213-58014  (91551-80840)
09330-00021  

SST
09241-11010  

Text in Illustration
*a Hold
V100135

Turn


g.

Remove the 3 nuts and supply pump assembly from the timing chain case assembly.


h.
A347064

Remove the O-ring from the supply pump assembly.