Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P0031).

P2195
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After the engine is fully warmed up, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph). While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor voltage is 2.12 V or more for 3.5 seconds
(2 trip detection logic)
·

Air fuel ratio sensor

·

ECM



MONITOR DESCRIPTION

When the air fuel sensor output indicates a lean value due to a malfunction in the sensor, the system cannot determine whether the air fuel ratio is rich and particulate matter may build up excessively in the DPF catalyst. The ECM monitors the air fuel ratio sensor voltage value when a fuel-cut is performed and detects whether this voltage value is abnormal. When the air fuel ratio sensor voltage value is 2.12 V or higher for 3.5 seconds or more, the ECM determines that the air fuel ratio sensor is malfunctioning and stores DTC P2195.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.REPLACE AIR FUEL RATIO SENSOR

NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for 30 seconds or more.


f.

Start the engine and warm it up.


g.

After the engine is fully warmed up, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph).

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P2195.


iii.

Check the DTC judgment result.

Result
GTS Display Result Proceed to
Pending DTC DTC P2195 is output B
All Readiness NORMAL A
ABNORMAL B

HINT:

If STATUS is INCOMPLETE or N/A, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph) again.





A

END

B