Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  DIAGNOSIS SYSTEM  


EURO-OBD


A208456

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the vehicle Engine Control Module (ECM) can then be read.

The Malfunction Indicator Lamp (MIL) is illuminated when the vehicle on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are stored in the ECM memory (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DIAGNOSTIC TROUBLE CODE CHART).

When the malfunction does not reoccur, the MIL stays illuminated until the engine switch is turned off, and the MIL turns off when the engine is started. Be aware that the DTCs remain stored in the ECM memory.

To check DTCs, connect the GTS to the DLC3 on the vehicle.


NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used when simulating malfunction symptoms to increase the ability of the system to detect malfunctions, including intermittent malfunctions (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>CHECK MODE PROCEDURE).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).


FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.


MIL


a.
A208456

The MIL illuminates when the engine switch is turned on (IG) and the engine is not running.

HINT:

If the MIL is not illuminated, check the MIL circuit (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>MIL Circuit).



b.

When the engine is started, the MIL should turn off. If the MIL remains on, the diagnosis system has detected a malfunction or abnormality in the ECD system.



ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

Check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Perform the DTC judgment driving pattern to run the DTC judgment.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


g.

Input the DTCs to be confirmed.


h.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit