Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P245C  Exhaust Gas Recirculation Cooler Bypass Control Circuit Low  P245D  Exhaust Gas Recirculation Cooler Bypass Control Circuit High  


DESCRIPTION

The No. 1 vacuum switching valve assembly (for EGR Bypass Valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

P245C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds or more Open or short in the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) for 3 seconds (1 trip detection logic).
·

Open or short in No. 1 vacuum switching valve assembly (for EGR Bypass Valve) circuit

·

No. 1 vacuum switching valve assembly (for EGR Bypass Valve)

·

ECM



P245D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 3 seconds or more Open or short in the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) for 3 seconds (1 trip detection logic).
·

Open or short in No. 1 vacuum switching valve assembly (for EGR Bypass Valve) circuit

·

No. 1 vacuum switching valve assembly (for EGR Bypass Valve)

·

ECM



WIRING DIAGRAM

A388917E03
0.542,5.99 1.615,6.188 1.073,0.198 10 false Battery 2.938,6.104 4.604,6.302 1.667,0.198 10 false No. 1 Integration Relay 0.406,5.25 1.479,5.448 1.073,0.198 10 false FL 0.406,4.344 0.854,4.542 0.448,0.198 10 false P/I-B 1.719,3.875 2.167,4.073 0.448,0.198 10 false 1C 2.49,5.177 3.604,5.385 1.115,0.208 10 false EFI-MAIN NO. 1 4.208,4.042 4.938,4.25 0.729,0.208 10 false EFI NO. 2 4.99,5.365 5.438,5.563 0.448,0.198 10 false 1K 6.229,5.25 6.781,5.448 0.552,0.198 10 false MREL 5.813,5.375 6.26,5.573 0.448,0.198 10 false G184 6.438,6.083 6.885,6.281 0.448,0.198 10 false ECM 2.469,4.031 3.583,4.24 1.115,0.208 10 false EFI-MAIN NO. 2 1.729,5.365 2.177,5.563 0.448,0.198 10 false 1J 4.979,3.875 5.427,4.073 0.448,0.198 10 false 1K 3.49,4.542 4.604,4.75 1.115,0.208 10 false EFI MAIN 2 3.5,5.698 4.615,5.906 1.115,0.208 10 false EFI MAIN 1 1.76,3.677 1.917,3.875 0.156,0.198 10 false 1 4.99,3.688 5.146,3.885 0.156,0.198 10 false 22 1.771,5.167 1.927,5.365 0.156,0.198 10 false 3 5.021,5.156 5.177,5.354 0.156,0.198 10 false 7 5.896,5.167 6.052,5.365 0.156,0.198 10 false 14 4.427,1.229 4.583,1.427 0.156,0.198 10 false 2 3.031,1.229 3.188,1.427 0.156,0.198 10 false 1 3.219,1.469 4.333,1.677 1.115,0.208 10 false C142 3.219,1.646 5.75,2.042 2.531,0.396 10 false No. 1 Vacuum Switching Valve Assembly (for EGR Bypass Valve) 5.813,1.094 6.26,1.292 0.448,0.198 10 false C149 6.229,1.094 6.792,1.292 0.563,0.198 10 false ECBV 5.896,0.885 6.167,1.083 0.271,0.198 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
a.

Inspect the No. 1 vacuum switching valve assembly (for EGR bypass valve) (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION).



OK

2.CHECK NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

5.REPLACE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
2.CHECK NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.
U169490E01
0.594,2.188 1.052,2.552 0.458,0.365 10 false C142 0.188,0 0.646,0.365 0.458,0.365 10 false *a

Disconnect the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C142-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Vacuum Switching Valve Assembly (for EGR Bypass Valve))


c.

Reconnect the No. 1 vacuum switching valve (for EGR Bypass Valve) connector.



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (NO. 1VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE) - ECM)
a.

Disconnect the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C142-2 (ECBV) - C149-16 (ECBV) Always Below 1 Ω
C142-2 (ECBV) or C149-16 (ECBV) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR BYPASS VALVE)
a.

Replace the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve assembly (for EGR Bypass Valve) connector is not 11 to 14 V, repair or replace the harness and connector between the No. 1 vacuum switching valve assembly (for EGR Bypass Valve) and No. 1 integration relay.




NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off wait 30 seconds.


d.

Turn the engine switch on (IG) for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END