Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0500  Vehicle Speed Sensor  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E40
0.427,1.052 1.573,1.427 1.146,0.375 10 from Wheel Speed Sensor 1.813,1.958 3.229,2.125 1.417,0.167 10 Skid Control ECU 3.719,1.958 4.927,2.375 1.208,0.417 10 Combination Meter Assembly 3.115,0.604 3.927,0.781 0.813,0.177 10 4-Pulse 5.042,0.604 5.854,0.781 0.813,0.177 10 4-Pulse 6.042,1.323 6.49,1.49 0.448,0.167 10 ECM

P0500
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle at 10 km/h (6.3 mph) or more for Automatic transmission:
Condition (a) is met for 5 seconds or more (2 trip detection logic):
(a) While vehicle being driven, no vehicle speed sensor signal transmitted to ECM.
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


for Manual transmission:
Conditions (a) and (b) are met for 20 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.

Related Data List
DTC No. Data List
P0500 Vehicle Speed

WIRING DIAGRAM

A335120E14
0.271,1.469 1.521,1.969 1.25,0.5 10 false from Brake Actuator Assembly 2.063,1.375 2.375,1.573 0.313,0.198 10 false 33 2.302,1.375 2.615,1.573 0.313,0.198 10 false SI 3.521,1.375 3.833,1.573 0.313,0.198 10 false +S 3.802,1.365 4.115,1.563 0.313,0.198 10 false 32 2.135,2.26 2.448,2.458 0.313,0.198 10 false G6 2.135,2.427 4.167,2.896 2.031,0.469 10 false Combination Meter Assembly 4.875,1.375 5.188,1.573 0.313,0.198 10 false 10 5.115,1.375 5.531,1.594 0.417,0.219 10 false SPD 5.5,2.292 5.958,2.49 0.458,0.198 10 false G184 5.51,2.458 6,2.688 0.49,0.229 10 false ECM 5.042,2.646 6.302,3.01 1.26,0.365 10 false to Other ECUs

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


d.

Drive the vehicle.


e.

Read the value displayed on the GTS.

Result
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-32 (+S) - G184-10 (SPD) Always Below 1 Ω
G6-32 (+S) or G184-10 (SPD) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit).



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Start the engine.


f.

Drive the vehicle at 10 km/h (6.3 mph) or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the pending DTC is not output again.



NEXT

END