Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the master cylinder solenoid*1 or brake actuator assembly (skid control ECU)*2.

*1: for 1GR-FE, 1KD-FTV, 1GD-FTV

*2: for 2TR-FE, 5L-E


WIRING DIAGRAM

E323268E01
0.309,1.075 2.039,1.231 1.730,0.156 10 Brake Actuator Assembly*1 0.309,0.935 2.039,1.090 1.730,0.156 10 A6 0.309,2.116 2.039,2.272 1.730,0.156 10 A7 0.309,2.247 2.039,2.403 1.730,0.156 10 Master Cylinder Solenoid*2 0.613,4.404 2.343,4.560 1.730,0.156 10 G120 0.613,4.563 2.221,4.900 1.608,0.336 10 Windshield Wiper Switch Assembly*6 0.073,7.19 2.552,7.331 2.479,0.140 10 *5: for RHD, RH Side Type 0.073,7.46 2.552,7.600 2.479,0.140 10 *6: w/ Auto Wipre System 0.073,7.729 2.552,7.869 2.479,0.140 10 *7: w/ Entry and Start System 0.073,7.998 2.552,8.139 2.479,0.140 10 *8: w/ Navigation System 0.073,8.268 3.875,8.408 3.802,0.140 10 *9: w/ Audio and Visual System (for Radio and Display Type) 0.073,8.537 3.792,8.677 3.719,0.140 10 *10: w/ Audio and Visual System (for Radio Receiver Type) 0.073,6.113 2.552,6.253 2.479,0.140 10 *1: for 2TR-FE, 5L-E 0.073,6.382 2.552,6.523 2.479,0.140 10 *2: for 1GR-FE, 1GD-FTV, 1KD-FTV 0.073,6.652 2.552,6.792 2.479,0.140 10 *3: for LHD 0.073,6.921 2.552,7.061 2.479,0.140 10 *4: for RHD, LH Side Type 5.054,3.335 6.913,3.491 1.858,0.156 10 G6 5.232,2.63 5.604,2.786 0.372,0.156 10 +S 4.998,2.63 5.371,2.786 0.372,0.156 10 32 5.232,0.29 5.604,0.446 0.372,0.156 10 SI 4.998,0.29 5.371,0.446 0.372,0.156 10 33 5.054,3.466 6.913,3.622 1.858,0.156 10 Combination Meter Assembly 2.932,2.74 3.304,2.895 0.372,0.156 10 3B 1.517,2.677 1.889,2.832 0.372,0.156 10 SPD 0.949,1.497 1.322,1.653 0.372,0.156 10 SP1 1.327,1.497 1.700,1.653 0.372,0.156 10 12 0.949,0.311 1.322,0.467 0.372,0.156 10 SP1 1.327,0.311 1.700,0.467 0.372,0.156 10 11 1.517,3.793 1.889,3.949 0.372,0.156 10 SPD 2.948,2.541 3.320,2.697 0.372,0.156 10 72 1.902,2.672 2.274,2.828 0.372,0.156 10 23 2.932,3.874 3.304,4.030 0.372,0.156 10 3C 3.833,2.74 4.205,2.895 0.372,0.156 10 3A 3.845,2.541 4.217,2.697 0.372,0.156 10 59 3.833,3.856 4.205,4.012 0.372,0.156 10 3A 3.845,3.657 4.217,3.813 0.372,0.156 10 22 2.948,3.676 3.320,3.832 0.372,0.156 10 24 1.909,3.622 2.385,3.947 0.477,0.325 10 6*3, *4 4*5 0.377,3.179 2.955,3.503 2.578,0.325 10 G51 0.377,3.328 2.955,3.653 2.578,0.325 10 Power Management Control ECU*7 2.871,7.839 4.373,7.995 1.502,0.156 10 No. 3 Junction Block 4.609,5.728 6.692,6.051 2.083,0.323 10 Navigation Receiver Assembly*8 4.609,5.584 6.165,5.906 1.555,0.323 10 H56 4.773,6.98 6.504,7.303 1.731,0.323 10 Radio and Display Receiver Assembly*9 4.773,8.353 6.652,8.516 1.879,0.163 10 H47 4.773,8.492 6.652,8.655 1.879,0.163 10 Radio Receiver Assembly*10 4.773,6.835 6.328,7.158 1.555,0.323 10 H51 4.739,4.568 6.241,4.724 1.502,0.156 10 Junction Connector 4.853,3.869 5.193,4.025 0.340,0.156 10 H24 4.853,4.261 5.193,4.417 0.340,0.156 10 H25 5.539,4.261 5.879,4.417 0.340,0.156 10 H25 5.903,4.172 6.244,4.328 0.340,0.156 10 10 4.582,4.172 4.922,4.328 0.340,0.156 10 11 4.666,3.766 5.006,3.922 0.340,0.156 10 2 5.874,4.909 6.246,5.065 0.372,0.156 10 SPD 6.259,4.918 6.631,5.074 0.372,0.156 10 17 5.874,6.142 6.246,6.298 0.372,0.156 10 SPD 6.259,6.151 6.631,6.307 0.372,0.156 10 17 5.874,7.655 6.246,7.811 0.372,0.156 10 SPD 6.259,7.664 6.631,7.820 0.372,0.156 10 17

E323269E01
5.216,3.161 7.011,3.501 1.795,0.340 10 Tire Pressure Monitor Receiver Assembly*1 2.843,1.716 4.144,1.864 1.301,0.148 10 No. 3 Junction Block 2.964,1.068 3.148,1.224 0.184,0.156 10 60 1.645,3.934 2.010,4.090 0.364,0.156 10 25*4 1.645,4.083 1.968,4.239 0.322,0.156 10 23*5 1.645,4.382 2.273,4.538 0.628,0.156 10 18*6, *10 1.645,4.233 2.264,4.388 0.619,0.156 10 12*6, *9 1.645,4.531 1.968,4.687 0.322,0.156 10 30*7 1.645,4.68 1.968,4.836 0.322,0.156 10 10*8 0.825,6.04 1.172,6.188 0.346,0.148 10 ECM 5.63,5.621 6.608,5.770 0.978,0.148 10 TCM*7, *9 0.236,3.545 1.919,3.701 1.684,0.156 10 Clearance Warning ECU*3 5.425,4.684 5.806,4.840 0.381,0.156 10 SPD1 1.239,3.027 1.548,3.183 0.309,0.156 10 SPD 1.064,4.63 1.588,4.786 0.524,0.156 10 SPD*11 1.064,4.49 1.588,4.646 0.524,0.156 10 SP1*4 1.656,3.022 1.972,3.177 0.316,0.156 10 3 5.169,4.685 5.352,4.841 0.184,0.156 10 25 2.962,4.587 3.146,4.742 0.184,0.156 10 96 2.962,4.783 3.151,4.939 0.189,0.156 10 4A 3.839,3.119 4.028,3.275 0.189,0.156 10 4A 2.961,3.119 3.149,3.275 0.189,0.156 10 4B 3.827,4.78 4.016,4.936 0.189,0.156 10 4B 3.889,4.59 4.001,4.746 0.112,0.156 10 1 3.838,2.916 4.027,3.072 0.189,0.156 10 48 2.953,1.256 3.142,1.412 0.189,0.156 10 3A 3.856,1.068 4.143,1.224 0.287,0.156 10 35 3.845,1.256 4.034,1.412 0.189,0.156 10 3A 5.237,2.998 5.549,3.154 0.311,0.156 10 R41 5.135,1.253 5.583,1.409 0.447,0.156 10 H63 5.109,1.421 6.904,1.761 1.795,0.340 10 Stereo Component Amplifier Assembly*2 2.96,2.919 3.149,3.075 0.189,0.156 10 49 0.825,5.082 1.356,5.238 0.531,0.156 10 G182*4 0.825,5.24 1.668,5.396 0.843,0.156 10 G181*5 0.825,5.398 1.633,5.554 0.808,0.156 10 G55*6, *10 0.825,5.567 1.622,5.722 0.796,0.156 10 G56*6, *9 0.825,5.717 1.256,5.873 0.431,0.156 10 G58*7 0.825,5.866 1.682,6.022 0.857,0.156 10 G184*8 5.637,5.435 5.924,5.583 0.287,0.148 10 G70 0.237,3.367 0.393,3.523 0.156,0.156 10 I1 0.232,6.629 2.570,6.778 2.338,0.149 10 *1: w/ Tire Pressure Monitor System 0.232,7.923 1.155,8.088 0.923,0.165 10 *5: for 2TR-FE 0.232,7.6 0.975,7.749 0.743,0.149 10 *4: for 5L-E 0.232,8.263 1.168,8.428 0.936,0.165 10 *6: for 1GR-FE 0.232,8.589 1.258,8.738 1.026,0.149 10 *7: for 1KD-FTV 0.232,7.276 3.108,7.425 2.876,0.149 10 *3: w/ TOYOTA Parking Assist-sensor System 0.232,6.953 2.395,7.102 2.163,0.149 10 *2: w/ Stereo Component Amplifier 3.333,6.629 5.671,6.778 2.338,0.149 10 *8: for 1GD-FTV 3.333,7.276 6.209,7.425 2.876,0.149 10 *10: for Manual Transmission 3.333,7.6 6.209,7.749 2.876,0.149 10 *11: except 5L-E 3.333,6.953 5.496,7.102 2.163,0.149 10 *9: for Automatic Transmission 2.851,5.218 4.153,5.366 1.301,0.148 10 No. 4 Junction Block 5.445,2.314 5.754,2.469 0.309,0.156 10 SPD 5.457,0.531 5.766,0.687 0.309,0.156 10 SPD 5.211,2.311 5.323,2.467 0.112,0.156 10 2 5.176,0.535 5.358,0.691 0.182,0.156 10 11

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (INPUT VOLTAGE)
a.
U170595E02
1.885,1.396 2.073,1.708 false 0.156,0.073 0.333,0.24 0.177,0.167 10 false *a 0.25,1.177 0.469,1.323 0.219,0.146 10 false G6 2.042,1.719 2.25,1.865 0.208,0.146 10 false +S

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-32 (+S) - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

for 1GR-FE, 1KD-FTV, 1GD-FTV:

i.

Disconnect the master cylinder solenoid (skid control ECU) connector.


ii.
U149350E03
2.521,0.927 2.208,1.573 false 0.115,0.417 0.292,0.583 0.177,0.167 10 false *a 1.615,0.813 1.833,0.958 0.219,0.146 10 false A7 2.573,0.813 2.854,0.958 0.281,0.146 10 false SP1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-12 (SP1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



b.

for 2TR-FE, 5L-E:

i.

Disconnect the brake actuator assembly (skid control ECU) connector.


ii.
U170657E02
2.531,0.594 2.188,1.531 false 0.125,0.073 0.302,0.24 0.177,0.167 10 false *a 1.625,0.469 1.844,0.615 0.219,0.146 10 false A6 2.583,0.469 2.865,0.615 0.281,0.146 10 false SP1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-11 (SP1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])




OK

3.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
3.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)
a.
U170649E02
1.5,1.271 1.01,1.76 1.01,1.76 0.906,1.76 false 0.719,1.677 0.885,1.823 0.167,0.146 10 false SI 0.146,0.073 0.313,0.219 0.167,0.146 10 false *a 0.271,1.021 0.5,1.167 0.229,0.146 10 false G6 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.521 3.302,3.667 0.333,0.146 10 false GND

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


ii.

Connect an oscilloscope to terminal G6-33 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Terminal No. (Symbol) G6-33 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h (12 mph)

Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

OK:

The waveform displayed is as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


Result
Result Proceed to
OK A
NG (for LHD, w/ Hydraulic Brake Booster) B
NG (for RHD, w/ Hydraulic Brake Booster) C
NG (w/ Vacuum Brake Booster) D




A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

D

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
a.

for 1GR-FE, 1KD-FTV, 1GD-FTV:

i.

Disconnect the G6 combination meter assembly connector.


ii.

Disconnect the A7 master cylinder solenoid (skid control ECU) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-33 (SI) - A7-12 (SP1) Always Below 1 Ω
A7-12 (SP1) - Body ground Always 10 kΩ or higher




b.

for 2TR-FE, 5L-E:

i.

Disconnect the G6 combination meter assembly connector.


ii.

Disconnect the A6 brake actuator assembly (skid control ECU) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-33 (SI) - A6-11 (SP1) Always Below 1 Ω
A6-11 (SP1) - Body ground Always 10 kΩ or higher





OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION BLOCK)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the 3A No. 3 junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-32 (+S) - 3A-59 Always Below 1 Ω
G6-32 (+S) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

HINT:

If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


i.

Disconnect the No. 3 junction block connectors.

U170650E02
5.313,0.854 5.74,0.625 false 5.333,2.688 5.677,2.979 false 5.333,4.125 5.771,4.313 false 5.156,3.729 5.708,3.49 false 5.25,3.854 5.823,3.76 false 5.677,2.458 6.5,2.458 false 6.542,2.385 6.708,2.552 0.167,0.167 10 false *a 3.75,0.49 3.948,0.635 0.198,0.146 10 false 3C 5.792,0.552 6.198,0.719 0.406,0.167 10 false 3C-24 5.74,2.906 6.125,3.073 0.385,0.167 10 false 3B-72 5.823,4.24 6.219,4.406 0.396,0.167 10 false 3A-60 1.729,0.958 1.896,1.125 0.167,0.167 10 false *1 3.771,1.875 3.969,2.021 0.198,0.146 10 false 3B 3.792,3.417 3.99,3.563 0.198,0.146 10 false 3A 5.76,3.406 6.219,3.573 0.458,0.167 10 false 3A-22 5.854,3.688 6.302,3.854 0.448,0.167 10 false 3A-35

Text in Illustration
*1 No. 3 Junction Block - -
*a Front view of wire harness connector
(to No. 3 Junction Block)
- -


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-24 - Body ground*1 Ignition switch ON 4.5 to 14 V
3B-72 - Body ground*2 Ignition switch ON 4.5 to 14 V
3A-22 - Body ground*3 Ignition switch ON 4.5 to 14 V
3A-60 - Body ground Ignition switch ON 4.5 to 14 V
3A-35 - Body ground*4 Ignition switch ON 4.5 to 14 V


*1: w/ Auto Wiper System

*2: w/ Entry and Start System

*3: w/ Audio and Visual System or Navigation System

*4: w/ Tire Pressure Monitor System


Result
Result Proceed to
Voltage is not as specified in one circuit A
Voltage is as specified in all circuits B




A

7.SYSTEM CHECK

B

REPLACE NO. 3 JUNCTION BLOCK

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not as specified in the previous step.

Result
Tester Connection System that Uses the Circuit Proceed to
3C-24 - Body ground Auto wiper system*1 A
3B-72 - Body ground Entry and start system*2 B
3A-22 - Body ground Audio and visual system*3 or navigation system*4 C
3A-60 - Body ground SFI system, TOYOTA parking assist-sensor system*5, automatic transmission system*6, *7 D
3A-35 - Body ground Tire pressure monitor system*8 E

*1: w/ Auto Wiper System

*2: w/ Entry and Start System

*3: w/ Audio and Visual System

*4: w/ Navigation System

*5: w/ TOYOTA Parking Assist-sensor System

*6: for 1KD-FTV

*7: for Automatic Transmission

*8: w/ Tire Pressure Monitor System




A

8.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - WINDSHIELD WIPER SWITCH ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU)

C

10.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - JUNCTION CONNECTOR)

D

16.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - NO. 4 JUNCTION BLOCK)

E

21.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - WINDSHIELD WIPER SWITCH ASSEMBLY)
a.

Disconnect the G120 auto wiper switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G120-6 (SPD) - Body ground*1, *2 Always 10 kΩ or higher
G120-4 (SPD) - Body ground*3 Always 10 kΩ or higher


*1: for LHD

*2: for RHD, LH Side Type

*3: for RHD, RH Side Type




OK

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-23 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - JUNCTION CONNECTOR)
a.

Disconnect the 3A No. 3 junction block connector.


b.

Disconnect the H24 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-22 - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
a.

Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

i.
U149351E01
0.59,0.277 0.760,0.447 0.170,0.170 10 *a 1.549,0.359 1.843,0.511 0.294,0.153 10 H25

Disconnect the junction connector.

Text in Illustration
*a Front view of wire harness connector
(Junction Connector)


ii.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H25-10 - Body ground*1 Ignition switch ON 4.5 to 14 V
H25-11 - Body ground*2 Ignition switch ON 4.5 to 14 V


*1: w/ Audio and Visual System or Navigation System

*2: w/ Stereo Component Amplifier


Result
Result Proceed to
NG (H25-10 - Body ground) (w/ Audio and Visual System [for Radio Receiver Type]) A
NG (H25-10 - Body ground) (w/ Audio and Visual System [for Radio and Display Type]) B
NG (H25-10 - Body ground) (w/ Navigation System) C
NG (H25-11 - Body ground) D
OK E




A

12.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY)

B

13.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

C

14.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

D

15.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - STEREO COMPONENT AMPLIFIER ASSEMBLY)

E

REPLACE JUNCTION CONNECTOR

12.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the H47 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H47-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H63 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H63-11 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - NO. 4 JUNCTION BLOCK)
a.

Disconnect the 3A No. 3 junction block connector.


b.

Disconnect the 4A No. 4 junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-60 (+S) - 4A-48 Always Below 1 Ω
3A-60 (+S) - Body ground Always 10 kΩ or higher




OK

17.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK)
a.

Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

i.

Disconnect the No. 4 junction block connectors.

U170651E02
4.385,1.948 4.76,1.76 4.76,1.76 5.688,1.76 false 5.344,4.448 5.667,4.427 false 4.385,2.479 4.74,2.896 4.74,2.896 5.625,2.896 false 6.094,3.208 6.24,3.208 false 3.792,1.74 3.99,1.885 0.198,0.146 10 false 4B 6.24,3.125 6.406,3.271 0.167,0.146 10 false *a 3.802,3.385 4.01,3.531 0.208,0.146 10 false 4A 5.677,2.844 6.083,2.99 0.406,0.146 10 false 4B-49 5.76,1.688 6.073,1.833 0.313,0.146 10 false 4B-1 5.729,4.354 6.146,4.5 0.417,0.146 10 false 4A-96 1.688,0.969 1.854,1.115 0.167,0.146 10 false *1

Text in Illustration
*1 No. 4 Junction Block - -
*a Front view of wire harness connector
(to No. 4 Junction Block)
- -


ii.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4B-49 - Body ground*1 Ignition switch ON 4.5 to 14 V
4B-1 - Body ground*2, *3 Ignition switch ON 4.5 to 14 V
4A-96 - Body ground Ignition switch ON 4.5 to 14 V


*1: w/ TOYOTA Parking Assist-sensor System

*2: for 1KD-FTV

*3: for Automatic Transmission


Result
Result Proceed to
NG (4B-49 - Body ground) A
NG (4B-1 - Body ground) B
NG (4A-96 - Body ground) C
OK D




A

18.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - CLEARANCE WARNING ECU)

B

19.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - TCM)

C

20.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - ECM)

D

REPLACE NO. 4 JUNCTION BLOCK

18.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - CLEARANCE WARNING ECU)
a.

Disconnect the I1 clearance warning ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-3 (SPD) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - TCM)
a.

Disconnect the G70 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-25 (SPD1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - ECM)
a.

Disconnect the G55*1, G56*2, G181*3, G58*4, G184*5 or G182*6 ECM connector.

*1: for 1GR-FE, Automatic Transmission

*2: for 1GR-FE, Manual Transmission

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV

*6: for 5L-E



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, Automatic Transmission
Tester Connection Condition Specified Condition
G56-12 (SPD) - Body ground Always 10 kΩ or higher

for 1GR-FE, Manual Transmission
Tester Connection Condition Specified Condition
G55-18 (SPD) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G181-23 (SPD) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G58-30 (SPD) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G184-10 (SPD) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G182-25 (SP1) - Body ground Always 10 kΩ or higher


HINT:
·

for 1GR-FE:

If it is necessary to replace the ECM, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL).

·

for 2TR-FE:

If it is necessary to replace the ECM, refer to the following procedures (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL).

·

for 1KD-FTV:

If it is necessary to replace the ECM, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).

·

for 1GD-FTV:

If it is necessary to replace the ECM, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL).

·

for 5L-E:

If it is necessary to replace the ECM, refer to the following procedures (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECM>REMOVAL).





OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (NO. 3 JUNCTION BLOCK - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY)
a.

Disconnect the R41 tire pressure monitor receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-2 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR