Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › MASS AIR FLOW METER › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260464 MASS AIR FLOW METER G

1GD-FTV ENGINE CONTROL  MASS AIR FLOW METER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 22204 1.CLEAN INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

NOTICE:

Do not loose a screw for fixing intake air flow meter sub-assembly. The resin of air cleaner cap sub-assembly would be damaged by repetition of fasten and loose more than 10 times.


a.
A356211

Disconnect the mass air flow meter sub-assembly connector and detach the 2 harness clamps.


b.
A492932

Detach the 4 clips.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly.


d.

Perform air blowing:

NOTICE:
A477847C01
1.74,1.781 2.375,1.042 2.375,1.042 2.542,1.042 true 1.51,2.552 0.667,2.781 0.667,2.781 0.531,2.781 true 1.5,0.417 1.25,0.417 1.25,0.417 0.917,0.667 true 1.25,0.417 1.083,0.667 true 2.563,0.958 2.792,1.125 0.229,0.167 10 true *1 0.302,2.698 0.521,2.865 0.219,0.167 10 true *a 1.719,1.896 1.927,2.052 0.208,0.156 10 false *c 2.365,4.323 2.583,4.49 0.219,0.167 10 true *b 1.5,0.333 1.75,0.5 0.25,0.167 10 true *c
*1 Intake Air Flow Meter Sub-assembly
*a Air Gun
*b 10 mm (0.3937 in.)
*c Air Flow Meter Exit Hole


Do not touch the tip of the air gun nozzle to the air flow meter, and do not insert the tip of the air gun nozzle into the air flow meter exit hole.


i.
A398469C01
0.125,0.125 0.365,0.302 0.24,0.177 10 false *a 1.313,0.24 1.552,0.406 0.24,0.167 10 false *b 1.563,0.573 1.792,0.74 0.229,0.167 10 false *c 0.688,0.906 0.927,1.083 0.24,0.177 10 false *d 0.677,1.708 0.917,1.885 0.24,0.177 10 false *e
*a Intermittently
*b 3 to 6 seconds
*c 1 second
*d On
*e Off


Intermittently air blow the intake air flow meter sub-assembly exit hole with a pressure of approximately 392 to 981 kPa (4.0 to 10.0 kgf/cm2, 57 to 142 psi) more than 10 times over 30 seconds or more.



e.

Attach the 4 clips to install the air cleaner cap sub-assembly.


f.

Tighten the hose clamp.

Torque:
5.0 N・m (51 kgf・cm, )


g.

Connect the mass air flow meter connector and attach the 2 wire harness clamps.


Hide 22204 2.INSPECT INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

a.

Read the value using the GTS (MAF).

NOTICE:

Perform the inspection of the intake mass air flow meter sub-assembly while it is installed to the air cleaner cap sub-assembly (installed to the vehicle).


i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


v.

Wait for 30 seconds, and read the value on the GTS.


If the result is not as specified, replace the intake mass air flow meter sub-assembly.

If the result is within the specified range, inspect the intake mass air flow meter sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).