Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2120).

P2121
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds or more.
·

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.

·

Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.


Either of the following conditions is met (1 trip detection logic):
1.

Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position)

2.

Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM



Related Data List
DTC No. Data List
P2121
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

NG

2.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Wait for 5 seconds after turning the engine switch on (IG).


e.

Turn the GTS on.


f.

Operate the accelerator pedal in accordance with the following procedure [B].

i.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.


ii.

Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.



g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
DTC P2121 is output A
No DTC is output B



A

4.REPLACE ECM

B

END

4.REPLACE ECM

NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Wait for 5 seconds after turning the engine switch on (IG).


e.

Turn the GTS on.


f.

Operate the accelerator pedal in accordance with the following procedure [B].

i.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.


ii.

Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.



g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.



NEXT

END