Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the pre-stroke control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A208460E63
2.781,0.51 2.938,0.365 2.938,0.365 2.99,0.365 false 3.135,2.198 3.24,2.146 3.24,2.146 3.281,2.146 false 1.948,1.646 2.177,1.646 false 2.229,1.104 2.5,1.104 false 1.406,0.531 0.938,0.646 false 0.063,0.042 1.792,0.271 1.729,0.229 10 false Property of Output Voltage: 1.052,0.406 1.417,0.594 0.365,0.188 10 false 5.00 0.625,0.573 0.948,0.813 0.323,0.24 10 false 4.90 2.208,1.573 2.958,1.844 0.75,0.271 10 false RR2 (Sub) 1.542,1.021 2.198,1.271 0.656,0.25 10 false RR (Main) 1.052,0.625 1.49,0.813 0.438,0.188 10 false 4.61 1.052,0.823 1.406,1.021 0.354,0.198 10 false 4.11 1.052,1.708 1.417,1.917 0.365,0.208 10 false 1.35 1.052,1.906 1.385,2.073 0.333,0.167 10 false 0.85 1.052,2.083 1.427,2.25 0.375,0.167 10 false 0.55 1.24,2.219 1.417,2.406 0.177,0.188 10 false 0 2.938,2.333 3.604,2.573 0.667,0.24 10 false 233000 1.125,2.438 3.24,2.667 2.115,0.229 10 false Common Rail Pressure (kPa) 3.323,2.063 4.219,2.281 0.896,0.219 10 false Stores P0192 3.021,0.281 3.969,0.563 0.948,0.281 10 false Stores P0193 0.063,1.115 1.25,1.406 1.188,0.292 10 false Output Voltage (V) 5.198,1.177 5.656,1.438 0.458,0.26 10 false Main 5.26,1.917 5.604,2.135 0.344,0.219 10 false Sub 6.729,1.177 7.156,1.365 0.427,0.188 10 false PCR1 6.74,1.375 7.104,1.563 0.365,0.188 10 false E2M 6.74,1.74 7.125,1.969 0.385,0.229 10 false VCS 6.729,1.938 7.146,2.156 0.417,0.219 10 false PCR2 5.875,0.625 6.365,0.833 0.49,0.208 10 false VCM 6.375,2.438 6.75,2.677 0.375,0.24 10 false E2S 4.219,0.042 6.729,0.542 2.51,0.5 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

P0087
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds Fuel pressure sensor output voltage stays at fixed value a certain number of times (0.1 seconds or more).
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Ran out of fuel

·

Fuel frozen

·

ECM



P0190
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0192
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



P0193
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)



Related Data List
DTC No. Data List
P0087
P0190
P0192
P0193
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure. Under stable conditions, the difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

-

Black smoke

-

Poor drivability

-

Lack of power

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Common Rail Pressure" always displays 0 kPa or 240000 kPa.



MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 30000 to 50000 kPa (306 to 510 kgf/cm2, 4350 to 7250 psi) when idling, and it increases to approximately 80000 to 110000 kPa (816 to 1122 kgf/cm2, 11600 to 15950 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the engine switch off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

A175676E08
4.99,0.885 5.458,0.521 5.458,0.521 5.615,0.521 false 4.802,1.771 4.677,1.771 4.677,1.771 4.188,1.427 false 0.063,0.031 1.917,0.302 1.854,0.271 10 false P0087 Malfunction Detection 2.271,0.552 3.229,0.771 0.958,0.219 10 false Fuel Pressure 4.844,1.677 5.51,1.875 0.667,0.198 10 false Abnormal 5.656,0.427 6.24,0.625 0.583,0.198 10 false Normal 2.292,2.156 3.302,2.417 1.01,0.26 10 false Engine Speed 5.229,3.375 5.635,3.583 0.406,0.208 10 false Time

·

Even if the system is normal, DTCs may be stored due to a drop in the fuel pressure after running out of fuel, etc. If DTCs P0087 and P1603 are both stored, clear these DTCs and perform a DTC check again.



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the engine switch off.


WIRING DIAGRAM

A351113E01
0.479,3.219 1.917,3.427 1.438,0.208 10 false Fuel Pressure Sensor 5.604,1.229 6.063,1.438 0.458,0.208 10 false VCM 5.271,2.438 5.448,2.646 0.177,0.208 10 false 33 5.25,0.323 5.427,0.531 0.177,0.208 10 false 18 5.271,1.594 5.531,1.802 0.26,0.208 10 false 26 5.271,2.021 5.469,2.229 0.198,0.208 10 false 25 5.26,1.177 5.479,1.385 0.219,0.208 10 false 28 5.26,0.76 5.479,0.969 0.219,0.208 10 false 19 5.604,0.385 6,0.594 0.396,0.208 10 false PCR1 5.604,0.802 6.052,1.01 0.448,0.208 10 false E2M 5.604,2.479 6.052,2.688 0.448,0.208 10 false VCS 5.604,1.635 6.042,1.844 0.438,0.208 10 false PCR2 5.604,2.063 6.188,2.271 0.583,0.208 10 false E2S 1.646,1.385 2.104,1.594 0.458,0.208 10 false VC 1.656,0.531 1.969,0.74 0.313,0.208 10 false PR 1.667,0.958 2.01,1.167 0.344,0.208 10 false E2 1.594,2.625 2.042,2.833 0.448,0.208 10 false VCS 1.604,1.802 2.042,2.01 0.438,0.208 10 false PR2 1.604,2.219 2.031,2.427 0.427,0.208 10 false E2S 2,1.063 2.208,1.271 0.208,0.208 10 false 4 2.01,1.5 2.219,1.708 0.208,0.208 10 false 6 2,0.646 2.208,0.854 0.208,0.208 10 false 5 2,2.75 2.208,2.958 0.208,0.208 10 false 1 2,2.333 2.208,2.542 0.208,0.208 10 false 3 2.01,1.917 2.177,2.167 0.167,0.25 10 false 2 6.052,3.177 6.448,3.375 0.396,0.198 10 false ECM 5.177,0.542 5.563,0.75 0.385,0.208 10 false C151 0.5,3.031 0.948,3.219 0.448,0.188 10 false r8 5.177,0.948 5.563,1.156 0.385,0.208 10 false C151 5.167,1.375 5.552,1.583 0.385,0.208 10 false C151 5.167,1.792 5.604,2 0.438,0.208 10 false C152 5.167,2.219 5.604,2.427 0.438,0.208 10 false C152 5.177,2.625 5.615,2.833 0.438,0.208 10 false C152

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0190, P0192 or P0193 is output A
DTC P0087 is output* B

HINT:

*: If DTCs P0087 and P1603 are stored, these DTCs may have been stored due to a drop in the fuel pressure after running out of fuel, etc. Therefore, clear these DTCs and perform a DTC check to confirm whether they are output again.




A

2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

B

10.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
U169385E01
1.615,1.635 0.792,2.458 false 1.656,1.688 1.271,2.438 false 1.781,1.677 2.094,2.448 false 2.677,2.469 1.823,1.635 false 0.135,0.052 0.354,0.25 0.219,0.198 10 false *a 1.292,0.948 1.677,1.104 0.385,0.156 10 false C151 0.135,2.458 0.792,2.667 0.656,0.208 10 false 19 (E2M) 0.99,2.458 1.646,2.667 0.656,0.208 10 false 28 (VCM) 1.854,2.458 2.49,2.667 0.635,0.208 10 false 33 (VCS) 2.688,2.458 3.25,2.635 0.563,0.177 10 false 25 (E2S) 1.833,0.938 2.219,1.094 0.385,0.156 10 false C152

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-28 (VCM) - C151-19 (E2M) Engine switch on (IG) 4.5 to 5.5 V
C152-33 (VCS) - C152-25 (E2S) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)

NG

8.REPLACE ECM
3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)
a.
U169386E01
1.615,1.646 0.792,2.448 false 1.667,1.646 1.271,2.698 false 1.781,1.635 2.219,2.677 false 2.688,2.458 1.823,1.635 false 0.135,0.052 0.354,0.25 0.219,0.198 10 false *a 1.302,0.938 1.688,1.094 0.385,0.156 10 false C151 0.135,2.458 0.792,2.667 0.656,0.208 10 false 19 (E2M) 0.865,2.708 1.573,2.917 0.708,0.208 10 false 18 (PCR1) 1.854,2.708 2.771,2.917 0.917,0.208 10 false 26 (PCR2) 2.688,2.458 3.25,2.635 0.563,0.177 10 false 25 (E2S) 1.823,0.938 2.208,1.094 0.385,0.156 10 false C152

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C151-18 (PCR1) - C151-19 (E2M) Idling 1.8 to 2.1 V
C152-26 (PCR2) - C152-25 (E2S) Idling 1.2 to 1.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the engine switch on (IG).


b.

Connect the GTS to the DLC3.



d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) for 1 second or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
DTC is not output B



A

8.REPLACE ECM

B

5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
U169121E01
0.169,0.112 0.389,0.291 0.221,0.179 10 *a 0.651,1.062 0.872,1.219 0.221,0.158 10 r8 0.83,0.494 1.195,0.652 0.365,0.158 10 VCS 0.807,1.663 1.056,1.821 0.249,0.158 10 E2 2.405,0.512 2.770,0.669 0.365,0.158 10 E2S 2.274,1.658 2.527,1.815 0.254,0.158 10 VC 1.435,1.005 1.057,0.703 false 1.991,1.005 2.501,0.703 false 0.931,1.644 1.441,1.342 false 2.351,1.636 1.973,1.333 false

Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
r8-6 (VC) - r8-4 (E2) Engine switch on (IG) 4.5 to 5.5 V
r8-1 (VCS) - r8-3 (E2S) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


c.

Reconnect the fuel pressure sensor connector.



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r8-5 (PR) - C151-18 (PCR1) Always Below 1 Ω
r8-4 (E2) - C151-19 (E2M) Always Below 1 Ω
r8-2 (PR2) - C152-26 (PCR2) Always Below 1 Ω
r8-3 (E2S) - C152-25 (E2S) Always Below 1 Ω
r8-5 (PR) or C151-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
r8-2 (PR2) or C152-26 (PCR2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the fuel pressure sensor connector.


e.

Reconnect the ECM connector.



OK

7.CHECK ECM (CHECK RESISTANCE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK ECM (CHECK RESISTANCE)
a.
U169120E01
0.169,0.112 0.389,0.291 0.221,0.179 10 *a 0.664,1.062 0.885,1.219 0.221,0.158 10 r8 0.83,0.494 1.195,0.652 0.365,0.158 10 VCS 0.807,1.663 1.056,1.821 0.249,0.158 10 E2 2.405,0.512 2.770,0.669 0.365,0.158 10 E2S 2.274,1.658 2.527,1.815 0.254,0.158 10 VC 1.435,1.005 1.057,0.703 false 1.991,1.005 2.501,0.703 false 0.931,1.644 1.441,1.342 false 2.351,1.636 1.973,1.333 false 1.901,0.145 2.266,0.303 0.365,0.158 10 PR2 1.311,1.881 1.606,2.039 0.295,0.158 10 PR 1.693,1.349 1.441,1.865 false 1.733,0.991 2.031,0.335 false

Disconnect the fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r8-6 (VC) - r8-5 (PR) Engine switch off No short or open circuit
r8-5 (PR) - r8-4 (E2) Engine switch off No short or open circuit
r8-1 (VCS) - r8-2 (PR2) Engine switch off No short or open circuit
r8-2 (PR2) - r8-3 (E2S) Engine switch off No short or open circuit


Text in Illustration
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


c.

Reconnect the fuel pressure sensor connector.



OK

10.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

8.REPLACE ECM
8.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.




NEXT

END