Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

P0627
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 1 second or more Even though the CPU (command area inside the ECU) is outputting the pre-stroke control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
·

Open or short in pre-stroke control valve circuit

·

Fuel supply pump assembly

·

ECM



Related Data List
DTC No. Data List
P0627
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DIAGRAM).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.

Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.



WIRING DIAGRAM

A348538E27
0.719,1.854 1.177,2.052 0.458,0.198 10 false r6 0.708,2.052 2.802,2.281 2.094,0.229 10 false Pre-stroke Control Valve 1.76,0.521 2.219,0.719 0.458,0.198 10 false +B 1.646,1.188 2.104,1.385 0.458,0.198 10 false PCV 5.677,0.646 6.313,0.844 0.635,0.198 10 false PCV+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false PCV- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C150 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 1 2.073,1.406 2.531,1.604 0.458,0.198 10 false 2 5.479,0.75 5.938,0.948 0.458,0.198 10 false 3 5.49,1.438 5.948,1.635 0.458,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Inspect the pre-stroke control valve (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
2.CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
a.

Disconnect the pre-stroke control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r6-1 - C150-3 (PCV+) Always Below 1 Ω
r6-2 - C150-4 (PCV-) Always Below 1 Ω
r6-1 (+B) or C150-3 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
r6-2 (PCV) or C150-4 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the pre-stroke control valve connector.


e.

Reconnect the ECM connector.



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
DTC P0627 is output B



A

END

B

6.REPLACE ECM
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
a.

Replace the fuel supply pump assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

6.REPLACE ECM
6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END