Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

Refer to DTC P2454 (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P2454).

HINT:
·

For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If P2453 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If the vacuum hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.



P2453
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine is running at 4000 rpm with no load for 10 seconds or more. When the output voltage from the differential pressure sensor indicates a reversal of positive and negative pressure.
(1 trip detection logic)
·

Incorrect air hose routing

·

Air hose is clogged

·

Blockage in vacuum pipe

·

Differential pressure sensor

·

ECM



Related Data List
DTC No. Data List
P2453 DPF Differential Pressure

HINT:
·

DTC P2454 (Diesel Particulate Filter Pressure Sensor "A" Circuit Low) and/or DTC P2455 (Diesel Particulate Filter Pressure Sensor "A" Circuit High) will be stored if there is an open or short malfunction in the differential pressure sensor circuit.

·

After confirming DTC P2453, check the differential pressure in "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" using the GTS.


Reference:
Condition DPF Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2453)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P2453 is output A
DTC P2453 and other DTCs are output B

HINT:

If codes other than P2453 are output, perform troubleshooting for those DTCs first.




A

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

B

2.CHECK CONNECTION OF AIR HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
a.

Check if the air hose routing between the differential pressure sensor and vacuum pipe is correct (See page Engine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>INSTALLATION).


A360341E03
4.396,2.135 4.99,1.563 4.99,1.563 5.083,1.563 true 2.198,1.417 2.292,1.417 2.292,1.417 2.698,2.01 true 3.688,1.031 4.521,0.302 4.521,0.302 4.615,0.302 true 2.917,0.323 3.01,0.323 3.01,0.323 3.417,0.917 true 2.74,0.25 3.052,0.406 0.313,0.156 10 false *1 4.656,0.229 4.969,0.385 0.313,0.156 10 false *2 2.042,1.354 2.354,1.51 0.313,0.156 10 false *3 5.125,1.49 5.438,1.646 0.313,0.156 10 false *4

Text in Illustration
*1 Air Hose (Downstream) *2 Air Hose (Upstream)
*3 No. 2 Vacuum Pipe *4 No. 1 Vacuum Pipe

b.

Check that there is no exhaust gas leakage between the differential pressure sensor and vacuum pipe.



OK

3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE

NG

5.CORRECT TO NORMAL CONNECTION
3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.
A362182E01
0.896,1.063 1.469,1.271 true 0.896,1.052 1.74,1.198 true 0.01,0.948 0.99,1.156 0.979,0.208 10 false Vacuum Hose

Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.




OK

4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)

NG

6.REPLACE CLOGGED PARTS
4.READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


d.

Check that the differential pressure is as specified below.

Result
Condition Differential Pressure Output Sensor Condition
Engine switch on (IG) Approximately 0 kPa Normal



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

7.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.CORRECT TO NORMAL CONNECTION

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CLOGGED PARTS

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.


NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


g.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition DPF Differential Pressure
2500 rpm without load 0.5 kPa or more




h.

Start the engine.


i.

Engine is running at 4000 rpm with no load for 10 seconds or more.


j.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


ii.

Input DTC P2453.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.




NEXT

END