Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0046  Turbocharger / Supercharger Boost Control "A" Circuit Range / Performance  P0047  Turbo / Super Charger Boost Control Solenoid Circuit Low  P0048  Turbo / Super Charger Boost Control Solenoid Circuit High  


DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

P0046
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more. The difference between the target VN opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more.
(1 trip detection logic)
·

Turbocharger nozzle vane control actuator

·

Turbocharger sub-assembly

·

Turbocharger nozzle vane is stuck or movement is irregular



P0047
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic).
·

Open in DC motor (turbocharger nozzle vane control actuator) circuit

·

Turbocharger nozzle vane control actuator

·

Turbocharger nozzle vane is stuck or movement is irregular



P0048
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic).
·

Short in DC motor (turbocharger nozzle vane control actuator) circuit

·

Turbocharger nozzle vane control actuator

·

Turbocharger nozzle vane is stuck or movement is irregular



HINT:
·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

-

Vehicle surge when driving with full load


·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load




WIRING DIAGRAM

A348538E01
0.719,1.854 1.177,2.052 0.458,0.198 10 false C141 0.729,2.052 1.51,2.25 0.781,0.198 10 false DC motor 1.76,0.521 2.219,0.719 0.458,0.198 10 false M+ 1.771,1.188 2.229,1.385 0.458,0.198 10 false M- 5.677,0.646 6.313,0.844 0.635,0.198 10 false VNM+ 5.677,1.292 6.292,1.479 0.615,0.188 10 false VNM- 5.979,1.813 6.438,2.01 0.458,0.198 10 false C151 5.99,1.99 6.448,2.188 0.458,0.198 10 false ECM 2.073,0.75 2.531,0.948 0.458,0.198 10 false 2 2.073,1.406 2.531,1.604 0.458,0.198 10 false 1 5.479,0.75 5.938,0.948 0.458,0.198 10 false 1 5.5,1.438 5.958,1.635 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0046 is output A
DTC P0047 and/or P0048 is output B
DTC P0046, P0047 and/or P0048 and other DTCs are output C

HINT:

If codes other than DTC P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

5.INSPECT TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (DC MOTORRESISTANCE)

C

2.INSPECT TURBOCHARGER NOZZLE VANE PLATE

b.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.


ii.
A348999

Move the turbocharger vane control rod subassembly and check that the turbocharger nozzle vane plate moves.

Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.





OK

3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

4.REPLACE TURBOCHARGER SUB-ASSEMBLY
3.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE TURBOCHARGER SUB-ASSEMBLY

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.INSPECT TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (DC MOTORRESISTANCE)
a.
C217215

Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (M-) - 2 (M+) Always 1 to 100 Ω


Text in Illustration
*a Component without harness connected
(DC Motor)


c.

Reconnect the DC motor connector.



OK

6.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

8.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
6.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C141-1 (M-) - C151-2 (VNM-) Always Below 1 Ω
C141-2 (M+) - C151-1 (VNM+) Always Below 1 Ω
C141-1 (M-) or C151-2 (VNM-) - Body ground and other terminals Always 10 kΩ or higher
C141-2 (M+) or C151-1 (VNM+) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the DC motor connector.


e.

Reconnect the ECM connector.



OK

7.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR
a.

Replace the turbocharger nozzle vane control actuator (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>DISASSEMBLY).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off and wait for 30 seconds or more.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.


g.

Maintain the Active Test "Activate the VN Turbo Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output again.



NEXT

END