Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › CYLINDER HEAD
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260476 CYLINDER HEAD A

5L-E ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.
A057248E04
1.594,1.052 1.073,0.531 1.073,0.531 1.615,1.354 false 0.729,0.417 1.156,0.688 0.427,0.271 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.


d.

Select a new guide bush.

New Guide Bush:
Item Specified Conditions
Bush Bore Diameter 13.004 to 13.025 mm (0.512 to 0.513 in.) 13.054 to 13.075 mm (0.514 to 0.515 in.)
Bush to be Used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 13.025 mm (0.513 in.), machine the bush bore to a dimension of 13.054 to 13.075 mm (0.514 to 0.515 in.).

If the bush bore diameter of the cylinder head is more than 13.075 mm (0.515 in.), replace the cylinder head.


e.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


f.
A070793E04
0.112,0.241 0.410,0.400 0.298,0.159 10 SST 0.915,0.756 0.52,0.361 0.52,0.361 0.932,1.332 false 3.247,0.64 3.399,0.796 0.152,0.156 10 *1

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09950-70010  (09951-07100)
09201-10000  (09201-01070)

Standard protrusion height:

10.8 to 11.2 mm (0.425 to 0.441 in.)


Text in Illustration
*1 Protrusion Height


g.
A056822E04
0.833,0.302 1,0.302 1,0.302 1.646,0.688 false 0.625,0.229 0.781,0.396 0.156,0.167 10 false *1

Using a sharp 8.0 mm reamer, ream the guide bush to obtain the specified clearance (See page Engine / Hybrid System>5L-E (ENGINE MECHANICAL)>CYLINDER HEAD>INSPECTION).

Text in Illustration
*1 Reamer


Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.
A057249E04
1.531,0.813 1.135,0.417 1.135,0.417 1.563,1.365 false 0.781,0.302 1.229,0.594 0.448,0.292 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.


d.

Select a new guide bush.

New Guide Bush:
Item Specified Conditions
Bush Bore Diameter 13.004 to 13.025 mm (0.512 to 0.513 in.) 13.054 to 13.075 mm (0.514 to 0.515 in.)
Bush to be Used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 13.025 mm (0.513 in.), machine the bush bore to a dimension of 13.054 to 13.075 mm (0.514 to 0.515 in.).

If the bush bore diameter of the cylinder head is more than 13.075 mm (0.515 in.), replace the cylinder head.


e.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


f.
A070794E06
0.823,0.823 0.458,0.375 0.458,0.375 0.844,1.406 false 0.063,0.26 0.49,0.521 0.427,0.26 10 false SST 3.156,0.573 3.313,0.729 0.156,0.156 10 false *1

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09950-70010  (09951-07100)
09201-10000  (09201-01070)

Standard protrusion height:

10.8 mm to 11.2 mm (0.425 to 0.441 in.)


Text in Illustration
*1 Protrusion Height


g.
A056823E04
1.646,0.656 1.188,0.26 1.188,0.26 1.073,0.26 false 0.813,0.146 0.979,0.333 0.167,0.188 10 false *1

Using a sharp 8.0 mm reamer, ream the guide bush to obtain the specified clearance (See page Engine / Hybrid System>5L-E (ENGINE MECHANICAL)>CYLINDER HEAD>INSPECTION).

Text in Illustration
*1 Reamer


Hide 3.REPLACE TIGHT PLUG

NOTICE:

If coolant leaks from the tight plug or the plug is corroded, replace it.


a.

Apply adhesive to new tight plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



b.

Install the tight plugs as shown in the illustration.

A378633E01
0.667,0.354 0.979,0.552 0.313,0.198 10 false *a 0.667,1.667 0.979,1.865 0.313,0.198 10 false *c 4.604,1.75 4.917,1.948 0.313,0.198 10 false *d 4.677,0.063 4.99,0.26 0.313,0.198 10 false *b 5.385,3.698 5.698,3.896 0.313,0.198 10 false *e 3.75,0.969 4.063,1.167 0.313,0.198 10 false A 4.396,0.969 4.708,1.167 0.313,0.198 10 false A 5.042,0.979 5.354,1.177 0.313,0.198 10 false A 5.698,0.979 6.01,1.177 0.313,0.198 10 false A 5.604,2.875 5.917,3.073 0.313,0.198 10 false A 4.958,2.885 5.271,3.083 0.313,0.198 10 false A 4.313,2.875 4.625,3.073 0.313,0.198 10 false A 1.646,2.188 1.958,2.385 0.313,0.198 10 false B 1.552,2.531 1.865,2.729 0.313,0.198 10 false C 1.323,0.802 1.635,0.969 0.313,0.167 10 true C

Text in Illustration
*a Front Side *b Cylinder Head Cover Side
*c Rear Side *d Intake Manifold Side
*e Stops - -


c.

Using SST, tap in the 7 tight plugs labeled A.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)


d.

Using SST, tap in the tight plug labeled B.

SST
09950-60010  (09951-00300)
09950-70010  (09951-07100)


e.

Using SST, tap in the 2 tight plugs labeled C.

SST
09950-60010  (09951-00450)
09950-70010  (09951-07100)


Hide 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Using a plastic-faced hammer, tap in a new ring pin until it stops.

A071264E07
1.104,0.198 1.281,0.375 0.177,0.177 10 false *a 5.135,1.427 5.313,1.604 0.177,0.177 10 false *b 4.219,2.375 4.427,2.635 0.208,0.26 10 false *c 2.021,1.802 2.188,1.979 0.167,0.177 10 false *1 2.594,1.354 2.76,1.51 0.167,0.156 10 false *2

Text in Illustration
*1 Height *2 Diameter
*a Front Side *b Cylinder Head Cover Side
*c Until pin stop - -

Standard Ring Pin:
Item Height Diameter
Ring pin 8 mm (0.315 in.) 11 mm (0.433 in.)