Home › Engine / Hybrid System › 1KD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053664 1KD-FTV ENGINE MECHANICAL _0260517 CYLINDER HEAD G

1KD-FTV ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the surface of the cylinder head that contacts the cylinder block.

NOTICE:

Be careful not to scratch the surface of the cylinder head.



b.

Using a soft brush and solvent, thoroughly clean the cylinder head.


c.
A059164

Using a valve guide bushing brush and solvent, clean all the guide bushes.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.
A380860E01
0.104,0.135 0.354,0.323 0.25,0.188 10 false *A 0.104,1.906 0.354,2.094 0.25,0.188 10 false *B 0.104,3.177 0.354,3.365 0.25,0.188 10 false *C

Inspect the cylinder head for warpage.

i.

Using a precision straightedge and feeler gauge, measure the surfaces of the cylinder head that contact the cylinder block and manifolds for warpage.

Maximum warpage:

0.15 mm (0.00591 in.)


Text in Illustration
*A Cylinder Block Side
*B Intake Manifold Side
*C Exhaust Manifold Side

If the warpage is more than the maximum, replace the cylinder head sub-assembly.



b.

Inspect the cylinder head for cracks.

i.

Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.

If there are cracks, replace the cylinder head sub-assembly.



Hide 13711 3.CLEAN INTAKE VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.


b.

Using a wire brush, thoroughly clean the valve.


Hide 13711 4.INSPECT INTAKE VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.970 to 5.985 mm (0.235 to 0.236 in.)


If the diameter is not as specified, replace the intake valve.


b.
A053834E10
3,1.781 3.177,1.948 0.177,0.167 10 false *1 0.135,1.708 1.021,1.854 0.885,0.146 6 false . 0.073,2.01 0.938,2.177 0.865,0.167 6 true .

Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


Text in Illustration
*1 Valve Face Angle

If the result is not as specified, replace the valve.



c.
A053643E06
0.448,1.646 0.656,1.813 0.208,0.167 10 false *1 0.094,2.042 0.542,2.167 0.448,0.125 6 true .

Check the valve head margin thickness.

Standard margin thickness:

1.1 mm (0.0433 in.)


Minimum margin thickness:

0.8 mm (0.0315 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the intake valve.


d.

Check the overall valve length.

Standard overall length:

105.15 to 105.75 mm (4.14 to 4.16 in.)


Minimum overall length:

104.65 mm (4.12 in.)


If the overall length is less than the minimum, replace the intake valve.


e.
A053828E04
0.104,2.01 0.521,2.167 0.417,0.156 6 true .

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the intake valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13715 5.CLEAN EXHAUST VALVE

a.

Using a gasket scraper, chip off any carbon from the valve head.


b.

Using a wire brush, thoroughly clean the exhaust valve.


Hide 13715 6.INSPECT EXHAUST VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

5.960 to 5.975 mm (0.2346 to 0.2352 in.)


If the diameter is not as specified, replace the valve.


b.
A053834E10
3,1.781 3.177,1.948 0.177,0.167 10 false *1 0.135,1.708 1.021,1.854 0.885,0.146 6 false . 0.073,2.01 0.938,2.177 0.865,0.167 6 true .

Check the valve face angle.

i.

Grind the valve enough to remove any pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°


Text in Illustration
*1 Valve Face Angle

If the result is not as specified, replace the exhaust valve.



c.
A053643E06
0.448,1.646 0.656,1.813 0.208,0.167 10 false *1 0.094,2.042 0.542,2.167 0.448,0.125 6 true .

Check the valve head margin thickness.

Standard margin thickness:

1.2 mm (0.0472 in.)


Minimum margin thickness:

0.7 mm (0.0276 in.)


Text in Illustration
*1 Margin Thickness

If the margin thickness is less than the minimum, replace the valve.


d.

Check the overall valve length.

Standard overall length:

105.02 to 105.62 mm (4.13 to 4.16 in.)


Minimum overall length:

104.52 mm (4.11 in.)


If the overall length is less than the minimum, replace the exhaust valve.


e.
A053828

Check the surface of the valve stem tip for wear.

If the valve stem tip is worn, resurface the tip with a grinder or replace the exhaust valve.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.



Hide 13711B 7.INSPECT INNER COMPRESSION SPRING

a.
A053807E11
1.177,0.042 1.354,0.219 0.177,0.177 10 false *1

Using a steel square, measure the deviation of the spring.

Maximum deviation:

2.0 mm (0.0787 in.)


Text in Illustration
*1 Deviation

If the deviation is more than the maximum, replace the inner compression spring.


b.
A061556

Using a vernier caliper, measure the free length of the spring.

Standard Free Length:
Item Specified Condition
w/ DPF 48.4 mm (1.91 in.)
w/o DPF 46.5 mm (1.83 in.)


If the free length is not as specified, replace the inner compression spring.


c.
EM00281

Using a spring tester, measure the tension of the valve spring at the specified installed length.

Standard tension (at 33.1 mm (1.303 in.)):

150 to 165 N (15.3 to 16.9 kgf, 33.7 to 37.0 lbf)


If the tension is not as specified, replace the inner compression spring.


Hide 11122 8.INSPECT INTAKE VALVE GUIDE BUSH

a.
A061557E03
0.021,1.917 0.198,2.083 0.177,0.167 6 true . 0.083,2.052 0.896,2.177 0.813,0.125 6 true . 0.74,1.292 0.958,1.469 0.219,0.177 6 true . 1.698,1.896 1.875,2.063 0.177,0.167 6 true .

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard valve guide bush inside diameter:

6.01 to 6.03 mm (0.2366 to 0.2374 in.)



b.

Subtract the valve stem diameter measurement (refer to the intake valve inspection procedures above) from the valve guide bush inside diameter measurement.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)


Maximum oil clearance:

0.08 mm (0.00315 in.)


If the oil clearance is more than the maximum, replace the intake valve and intake valve guide bush.


Hide 11126 9.INSPECT EXHAUST VALVE GUIDE BUSH

a.
A061558E04
0.063,2.083 0.875,2.177 0.813,0.094 6 false . 0.042,2.042 0.896,2.177 0.854,0.135 6 true . 0.031,1.906 0.167,2.052 0.135,0.146 6 true . 1.719,1.917 1.854,2.063 0.135,0.146 6 true . 0.74,1.302 0.958,1.438 0.219,0.135 6 true .

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard valve guide bush inside diameter:

6.01 to 6.03 mm (0.2366 to 0.2374 in.)



b.

Subtract the valve stem diameter measurement (refer to the exhaust valve inspection procedures above) from the valve guide bush inside diameter measurement.

Standard oil clearance:

0.035 to 0.070 mm (0.00138 to 0.00276 in.)


Maximum oil clearance:

0.10 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the valve and guide bush.


Hide 10.INSPECT INTAKE VALVE SEAT

a.
A059929E06
1.844,0.99 1.344,0.26 1.344,0.26 1.271,0.26 false 1.073,0.177 1.24,0.333 0.167,0.156 10 false *1

Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.

Text in Illustration
*1 45° Carbide Cutter


b.
A059921E02
1.677,1.115 1.865,1.281 0.188,0.167 10 false *1

Apply a light coat of Prussian blue to the valve face.


c.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve against the valve seat.



d.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.2 and 1.6 mm (0.0472 and 0.0630 in.).

Text in Illustration
*1 Width

If the contact surfaces are not as specified, resurface the valve intake seat. If necessary, replace the intake valve.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If the contact surfaces are not as specified, resurface the intake valve seat. If necessary, replace the intake valve.



Hide 11.INSPECT EXHAUST VALVE SEAT

a.
A058112E04
1.865,0.281 2.271,0.146 2.271,0.146 2.375,0.146 false 2.385,0.052 2.542,0.208 0.156,0.156 10 false *1

Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.

Text in Illustration
*1 45° Carbide Cutter


b.
A059921E02
1.677,1.115 1.865,1.281 0.188,0.167 10 false *1

Apply a light coat of Prussian blue to the valve face.


c.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve against the valve seat.



d.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.6 and 2.0 mm (0.0630 and 0.0787 in.)

Text in Illustration
*1 Width

If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.