Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT G

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT NO. 1 CHAIN SUB-ASSEMBLY

a.
A345790E01
1.608,1.161 1.793,1.315 0.185,0.155 10 *a 2.825,1.78 3.057,1.942 0.232,0.162 10 16 0.465,1.78 0.631,1.942 0.166,0.162 10 1 0.649,1.78 0.815,1.942 0.166,0.162 10 2 1.019,1.78 1.185,1.942 0.166,0.162 10 4 0.847,1.78 1.013,1.942 0.166,0.162 10 3 1.213,1.78 1.379,1.942 0.166,0.162 10 5 1.395,1.78 1.561,1.942 0.166,0.162 10 6

Using a spring scale, pull the No. 1 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

Text in Illustration
*a Measuring Point


b.

Using a vernier caliper, measure the length of 16 pins.

Maximum chain elongation:

144.7 mm (5.70 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 1 chain sub-assembly.


Hide 13507 2.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A345791E01
1.608,1.161 1.793,1.315 0.185,0.155 10 *a 2.871,1.78 3.103,1.942 0.232,0.162 10 16 0.462,1.78 0.628,1.942 0.166,0.162 10 1 0.623,1.78 0.789,1.942 0.166,0.162 10 2 0.946,1.78 1.112,1.942 0.166,0.162 10 4 0.793,1.78 0.960,1.942 0.166,0.162 10 3 1.122,1.78 1.288,1.942 0.166,0.162 10 5 1.288,1.78 1.455,1.942 0.166,0.162 10 6

Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

Text in Illustration
*a Measuring Point


b.

Using a vernier caliper, measure the length of 16 pins.

Maximum chain elongation:

121.6 mm (4.79 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13508E 3.INSPECT NO. 3 CHAIN SUB-ASSEMBLY

a.
A347352E01
1.61,1.096 1.795,1.250 0.185,0.155 10 *a 2.863,1.787 3.094,1.949 0.232,0.162 10 16 0.476,1.798 0.642,1.959 0.166,0.162 10 1 0.647,1.798 0.814,1.959 0.166,0.162 10 2 0.97,1.798 1.137,1.959 0.166,0.162 10 4 0.814,1.798 0.980,1.959 0.166,0.162 10 3 1.139,1.798 1.305,1.959 0.166,0.162 10 5 1.306,1.798 1.472,1.959 0.166,0.162 10 6

Using a spring scale, pull the No. 3 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

Text in Illustration
*a Measuring Point


b.

Using a vernier caliper, measure the length of 16 pins.

Maximum chain elongation:

121.6 mm (4.79 in.)


HINT:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 3 chain sub-assembly.


Hide 13540 4.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

·
A347238E01
1.704,0.281 1.889,0.436 0.185,0.155 10 *a 2.317,0.935 2.502,1.090 0.185,0.155 10 *b 1.593,1.582 1.778,1.737 0.185,0.155 10 *c 1.079,0.379 1.672,0.379 false 1.694,1.035 2.287,1.035 false 1.802,1.69 2.36,1.69 false

Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 1 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.
A346658E01
2.283,0.557 2.467,0.712 0.185,0.155 10 *a 1.702,0.663 2.252,0.663 false

Push the plunger and check that it moves smoothly.

Text in Illustration
*a Plunger

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 5.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A345792E01
2.267,1.866 2.452,2.020 0.185,0.155 10 *a 2.686,0.441 2.871,0.596 0.185,0.155 10 *b 2.339,1.035 2.482,0.542 2.482,0.542 2.656,0.542 false 1.942,1.764 2.068,1.964 2.068,1.964 2.241,1.964 false

Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.

Text in Illustration
*a Stopper Plate
*b Plunger

If necessary, replace the No. 2 chain tensioner assembly.


Hide 13560A 6.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 3 chain tensioner assembly, the plunger and 2 springs may come off of the No. 3 chain tensioner assembly body, but this is not a malfunction.

·
A347346E01
0.554,1.812 0.739,1.967 0.185,0.155 10 *a 1.372,1.682 1.557,1.837 0.185,0.155 10 *b 2.942,1.784 3.127,1.939 0.185,0.155 10 *c 0.667,1.277 0.667,1.814 false 1.457,1.127 1.457,1.664 false 2.368,1.397 2.552,1.551 0.185,0.155 10 *b 2.453,0.842 2.453,1.379 false 3.051,1.323 3.051,1.78 false

Before installing the plunger and 2 springs to the No. 3 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 3 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.
A347353E01
0.897,0.577 1.082,0.731 0.185,0.155 10 *a 1.103,0.686 1.26,0.686 1.26,0.686 1.333,1.098 false

Push the plunger and check that it moves smoothly.

Text in Illustration
*a Plunger

If necessary, replace the No. 3 chain tensioner assembly.


Hide 13523 7.INSPECT CAMSHAFT TIMING SPROCKET

a.

Wrap the No. 2 chain sub-assembly around the camshaft timing sprocket.


b.
A345793

Using a vernier caliper, measure the camshaft timing sprocket diameter with the No. 2 chain sub-assembly.

Minimum sprocket with chain diameter:

95.13 mm (3.75 in.)


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and camshaft timing sprocket.

HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.



Hide 13521 8.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Wrap the No. 1 chain sub-assembly around the crankshaft timing sprocket.


b.
A345794

Using a vernier caliper, measure the crankshaft timing sprocket diameter with the No. 1 chain sub-assembly.

Minimum sprocket with chain diameter:

68.59 mm (2.70 in.)


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and crankshaft timing sprocket.

HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.



Hide 13613 9.INSPECT INJECTION PUMP DRIVE GEAR

a.

for No. 1 Chain Sub-assembly Side:

i.

Wrap the No. 1 chain sub-assembly around the injection pump drive gear.


ii.
A345796

Using a vernier caliper, measure the injection pump drive gear diameter with the No. 1 chain sub-assembly.

Minimum gear with chain diameter:

68.59 mm (2.70 in.)


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and injection pump drive gear.

HINT:

The vernier caliper must contact the No. 1 chain sub-assembly rollers for the measurement.




b.

for No. 2 Chain Sub-assembly Side:

i.

Wrap the No. 2 chain sub-assembly around the injection pump drive gear.


ii.
A345795

Using a vernier caliper, measure the injection pump drive gear diameter with the No. 2 chain sub-assembly.

Minimum gear with chain diameter:

49.32 mm (1.94 in.)


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and injection pump drive gear.

HINT:

The vernier caliper must contact the No. 2 chain sub-assembly rollers for the measurement.




Hide 13639 10.INSPECT BALANCE SHAFT TIMING SPROCKET

a.

Wrap the No. 3 chain sub-assembly around the balance shaft timing sprocket.


b.
A347354

Using a vernier caliper, measure the balance shaft timing sprocket diameter with the No. 3 chain sub-assembly.

Minimum sprocket with chain diameter:

84.91 mm (3.34 in.)


If the diameter is less than the minimum, replace the No. 3 chain sub-assembly and balance shaft timing sprocket.

HINT:

The vernier caliper must contact the No. 3 chain sub-assembly rollers for the measurement.



Hide 13603B 11.INSPECT BALANCE SHAFT GEAR SUB-ASSEMBLY

a.

Wrap the No. 3 chain sub-assembly around the balance shaft gear sub-assembly.


b.
A347355

Using a vernier caliper, measure the balance shaft gear sub-assembly diameter with the No. 3 chain sub-assembly.

Minimum sprocket with chain diameter:

54.45 mm (2.14 in.)


If the diameter is less than the minimum, replace the No. 3 chain sub-assembly and balance shaft gear sub-assembly.

HINT:

The vernier caliper must contact the No. 3 chain sub-assembly rollers for the measurement.



Hide 13559 12.INSPECT NO. 1 CHAIN TENSIONER SLIPPER

a.
A345797E01
3.038,1.099 3.223,1.254 0.185,0.155 10 *a

Measure the depth of wear of the No. 1 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*a Depth

If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


Hide 13.INSPECT NO. 2 CHAIN TENSIONER SLIPPER

a.
A345798E01
3.044,1.096 3.229,1.251 0.185,0.155 10 *a

Measure the depth of wear of the No. 2 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*a Depth

If the depth is more than the maximum, replace the No. 2 chain tensioner slipper.


Hide 13561 14.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A345799E01
2.894,1.002 3.079,1.156 0.185,0.155 10 *a

Measure the depth of wear of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*a Depth

If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 15.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A345800E01
3.038,1.102 3.223,1.257 0.185,0.155 10 *a

Measure the depth of wear of the No. 2 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*a Depth

If the depth is more than the maximum, replace the No. 2 chain vibration damper.


Hide 13566B 16.INSPECT TIMING CHAIN GUIDE

a.
A343586E01
3.115,1.275 3.300,1.430 0.185,0.155 10 *a

Measure the depth of wear of the timing chain guide.

Maximum depth:

1.0 mm (0.0394 in.)


Text in Illustration
*a Depth

If the depth is more than the maximum, replace the timing chain guide.


Hide 17111 17.INSPECT INTAKE MANIFOLD

a.
A345801

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the intake manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the intake manifold.


Hide 17141 18.INSPECT EXHAUST MANIFOLD

a.
A345802

Using a precision straightedge and feeler gauge, measure the warpage of the surface where the exhaust manifold contacts the cylinder head sub-assembly.

Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the exhaust manifold.


Hide 13511 19.INSPECT CAMSHAFT

a.

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.425 to 41.525 mm (1.631 to 1.635 in.)


Minimum cam lobe height:

41.375 mm (1.629 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.356 to 1.357 in.)
Other journals 22.990 to 23.007 mm (0.905 to 0.906 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 13512 20.INSPECT NO. 2 CAMSHAFT

a.

Inspect the No. 2 camshaft runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the No. 2 camshaft.

HINT:

Check the oil clearance after replacing the No. 2 camshaft.




b.

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

41.694 to 41.794 mm (1.641 to 1.645 in.)


Minimum cam lobe height:

41.644 mm (1.640 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.356 to 1.357 in.)
Other journals 22.990 to 23.007 mm (0.905 to 0.906 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 21.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing caps, camshaft journals and No. 2 camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the cylinder head sub-assembly.


c.
A347311E01
0.388,0.27 0.573,0.425 0.185,0.155 10 *a 0.598,0.381 0.787,0.381 0.787,0.381 1.626,1.16 false

Lay a strip of Plastigage across each of the camshaft journals.

Text in Illustration
*a Plastigage


d.

Install the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps to the cylinder head sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY).

NOTICE:

Do not turn the camshaft and No. 2 camshaft.



e.

Remove the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps from the cylinder head sub-assembly (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).


f.
A347310

Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.040 to 0.077 mm (0.00157 to 0.00303 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.117 mm (0.00461 in.)
Other journals 0.102 mm (0.00402 in.)


If the camshaft oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.


g.

Completely remove the Plastigage from the camshaft journals.


Hide 11101A 22.INSPECT CYLINDER HEAD SET BOLT

a.

w/ Washer:

i.
A345806E01
2.33,0.343 2.515,0.498 0.185,0.155 10 *a 0.48,1.861 0.665,2.016 0.185,0.155 10 *b 0.565,1.345 0.565,1.843 false

Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

Minimum diameter:

11.4 mm (0.449 in.)


Text in Illustration
*a Measuring Area
*b Washer

If the diameter is less than the minimum, replace the cylinder head set bolt.



b.

w/o Washer:

i.
A345805E01
2.624,0.346 2.809,0.501 0.185,0.155 10 *a

Using a vernier caliper, measure the thread outside diameter of the cylinder head set bolt.

Minimum diameter:

12.8 mm (0.504 in.)


Text in Illustration
*a Measuring Area

If the diameter is less than the minimum, replace the cylinder head set bolt and cylinder head set bolt spacer.



Hide 13801 23.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand and check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 24.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign matter.

·

Use only clean engine oil.



a.

Place the valve lash adjuster assembly into a container full of new engine oil.

A345808E01
1.198,0.635 1.625,0.635 false 2.958,0.635 3.385,0.635 false 0.99,1.01 1.625,1.01 false 1.115,1.177 1.625,1.177 false 0.99,1.75 1.625,1.75 false 0.906,2.198 1.625,2.198 false 1.052,2.375 1.625,2.375 false 4.49,1.01 4.625,1.01 4.625,1.01 4.99,1.229 false 0.823,0.146 1.01,0.302 0.188,0.156 10 false *a 2.563,0.146 2.75,0.302 0.188,0.156 10 false *b 1.646,0.875 1.833,1.031 0.188,0.156 10 false *c 1.646,1.104 1.833,1.26 0.188,0.156 10 false *d 1.646,1.667 1.833,1.823 0.188,0.156 10 false *e 1.646,2.073 1.833,2.229 0.188,0.156 10 false *f 1.646,2.24 1.833,2.438 0.188,0.198 10 false *g 1.667,0.573 2.021,0.74 0.354,0.167 10 false SST 3.438,0.573 3.792,0.74 0.354,0.167 10 false SST 4.177,0.938 4.531,1.104 0.354,0.167 10 false SST

Text in Illustration
*a CORRECT *b INCORRECT
*c Taper Part *d Plunger
*e Low Pressure Chamber *f Check Ball
*g High Pressure Chamber - -


b.

Insert the tip of SST into the plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13620B 25.INSPECT ENGINE BALANCER ASSEMBLY

a.

Inspect the balance shaft thrust clearance.

i.
A347356

Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

Standard thrust clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum thrust clearance:

0.09 mm (0.00354 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.



b.

Inspect the balance shaft thrust backlash.

i.
A347357E01
1.587,1.654 1.904,1.908 0.317,0.254 2.328,1.393 2.513,1.548 0.185,0.155 10 *a 0.957,1.384 1.141,1.539 0.185,0.155 10 *b 1.645,1.688 1.830,1.842 0.185,0.155 10 *c

Fix the No. 2 balance shaft in place, and then, using a dial indicator, measure the backlash of the No. 1 and No. 2 balance shafts as shown in the illustration.

Standard backlash:

0.01 to 0.12 mm (0.000394 to 0.00472 in.)


Maximum backlash:

0.12 mm (0.00472 in.)


Text in Illustration
*a No. 2 Balance Shaft Side
*b No. 1 Balance Shaft Side
*c Fix

If the backlash is more than the maximum, replace the engine balancer assembly.