Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.

for Timing Chain Cover Sub-assembly Side:

i.
A343571E01
2.305,2.524 2.489,2.679 0.185,0.155 10 *a

Using a plastic-faced hammer, tap in 2 new straight pins to the timing chain cover sub-assembly.

Standard protrusion height:

5.0 to 7.0 mm (0.197 to 0.276 in.)


Text in Illustration
*a Protrusion Height



b.

for Timing Chain Case Assembly Side:

i.
A343556E01
2.282,2.484 2.467,2.639 0.185,0.155 10 *a

Using a plastic-faced hammer, tap in a new straight pin to the timing chain case assembly.

Standard protrusion height:

18 to 20 mm (0.709 to 0.787 in.)


Text in Illustration
*a Protrusion Height



Hide 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

for Timing Chain Cover Sub-assembly Side:

i.
A343572E01
1.806,3.255 1.991,3.410 0.185,0.155 10 *a 1.806,4.042 1.991,4.197 0.185,0.155 10 *b 2.378,3.588 2.563,3.742 0.185,0.155 10 *c

Using an E6 "TORX" socket wrench, install the stud bolts to the timing chain cover sub-assembly.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Text in Illustration
*a 16 mm (0.630 in.)
*b 9.0 mm (0.354 in.)
*c 27 mm (1.06 in.)



b.

for Timing Chain Case Assembly Side:

i.
A343557E01
1.924,2.296 2.109,2.451 0.185,0.155 10 *a 1.924,3.042 2.109,3.197 0.185,0.155 10 *b 2.477,2.639 2.662,2.794 0.185,0.155 10 *c

Using an E8 "TORX" socket wrench, install the stud bolts to the timing chain case assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a 19 mm (0.748 in.)
*b 16 mm (0.630 in.)
*c 44 mm (1.73 in.)



c.
A354149E01
2.107,2.45 2.292,2.605 0.185,0.155 10 *a 2.107,2.849 2.292,3.004 0.185,0.155 10 *a 2.58,2.684 2.764,2.839 0.185,0.155 10 *b

Using an E6 "TORX" socket wrench, install the stud bolt to the timing chain case assembly.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Text in Illustration
*a 9.0 mm (0.354 in.)
*b 19 mm (0.748 in.)


d.

for Oil Pan Sub-assembly Side:

i.
A347369E01
1.907,2.574 2.092,2.729 0.185,0.155 10 *a 1.907,3.021 2.092,3.176 0.185,0.155 10 *a 2.377,2.768 2.562,2.923 0.185,0.155 10 *b

Using an E6 "TORX" socket wrench, install the 2 stud bolts to the oil pan sub-assembly.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Text in Illustration
*a 9.0 mm (0.354 in.)
*b 19 mm (0.748 in.)



Hide 13577D 3.INSTALL LOCK PLATE

a.
A343552E01
0.604,1.219 1.406,1.219 true 2.135,1.896 2.323,2.052 0.188,0.156 10 false *a 0.375,1.115 0.594,1.313 0.219,0.198 10 true *b

Install the lock plate to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a Cylinder Block Sub-assembly Side
*b Oil Jet

HINT:
·

Make sure the lock plate is facing the direction shown in the illustration.

·

Make sure the end of the lock plate is holding the oil jet as shown in the illustration.




Hide 13750 6.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.


Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A346673E02
1.178,0.024 1.363,0.178 0.185,0.155 10 *1 1.517,1.569 1.701,1.724 0.185,0.155 10 *2 0.1,0.867 0.284,1.022 0.185,0.155 10 *3 0.311,0.959 0.907,0.959 false 1.728,1.671 2.273,1.671 false 1.385,0.116 1.549,0.116 1.549,0.116 1.675,0.49 false

Check that the No. 1 valve rocker arm sub-assembly is firmly set to the valve lash adjuster assembly.

Text in Illustration
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash adjuster assembly


b.

Apply a light coat of engine oil to the camshaft journals of the cylinder head sub-assembly and the thrust portion of the camshaft.


c.

Install the 16 No. 1 valve rocker arm sub-assemblies to the 16 valve lash adjuster assemblies.


Hide 13512 8.INSTALL NO. 2 CAMSHAFT

HINT:
A343553E01
1.635,1.552 1.820,1.707 0.185,0.155 10 *a 2.739,1.668 1.852,1.668 false 2.739,1.257 2.049,1.257 2.049,1.257 2.049,1.668 false

The glove is at the rear end of the No. 2 camshaft.


Text in Illustration
*a Glove
V100135

Engine Front Side

a.

Clean the No. 2 camshaft journals.


b.

Apply a light coat of engine oil to the No. 2 camshaft journals of the cylinder head sub-assembly and the thrust portion of the No. 2 camshaft.


Hide 13511 9.INSTALL CAMSHAFT

a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals of the cylinder head sub-assembly and the thrust portion of the camshaft.


c.
A343554E01
0.785,0.107 0.969,0.261 0.185,0.155 10 *a 0.993,0.214 1.178,0.214 1.178,0.214 1.178,0.604 false 1.849,0.107 2.033,0.261 0.185,0.155 10 *a 2.057,0.214 2.242,0.214 2.242,0.214 2.242,0.604 false

Make sure the knock pins of the camshaft and No. 2 camshaft are facing the direction shown in the illustration.

Text in Illustration
*a Knock Pin


Hide 10.INSTALL NO. 1 AND NO. 2 CAMSHAFT BEARING CAP

a.
A347239

Set the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps to the cylinder head sub-assembly as shown in the illustration.


b.

Temporarily install the 20 camshaft bearing cap bolts.


c.
A347241E01
1.313,1.146 1.469,1.302 0.156,0.156 10 true 3 0.365,0.031 0.583,0.188 0.219,0.156 10 false 20 0.354,1.896 0.573,2.052 0.219,0.156 10 false 19 0.052,0.625 0.271,0.781 0.219,0.156 10 false 18 0.052,1.302 0.271,1.458 0.219,0.156 10 false 17 2.719,0.167 2.938,0.323 0.219,0.156 10 false 16 2.708,1.771 2.927,1.927 0.219,0.156 10 false 14 0.823,0.177 1.042,0.333 0.219,0.156 10 false 12 0.823,1.771 1.042,1.927 0.219,0.156 10 false 10 2.146,0.167 2.271,0.323 0.125,0.156 10 false 8 2.135,1.771 2.26,1.927 0.125,0.156 10 false 6 1.5,0.177 1.625,0.333 0.125,0.156 10 false 4 1.51,1.771 1.635,1.927 0.125,0.156 10 false 2 2.927,0.792 3.167,1 0.24,0.208 10 true 13 2.479,1.156 2.698,1.313 0.219,0.156 10 true 15 2.333,0.792 2.51,0.969 0.177,0.177 10 true 5 1.948,1.156 2.083,1.344 0.135,0.188 10 true 7 1.698,0.792 1.865,0.979 0.167,0.188 10 true 1 1.073,0.792 1.219,0.969 0.146,0.177 10 true 9 0.625,1.156 0.854,1.333 0.229,0.177 10 true 11

Uniformly tighten the 20 camshaft bearing cap bolts in several steps in the order shown in the illustration.

Torque:
for camshaft bearing cap bolt A (No. 1 camshaft bearing) : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for camshaft bearing cap bolt B (No. 2 camshaft bearing) : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Camshaft Bearing Cap Bolt A
V100136

Camshaft Bearing Cap Bolt B


Hide 11.INSTALL NO. 3 CAMSHAFT BEARING CAP

a.

Clean and degrease the contact surfaces of the No. 3 camshaft bearing cap and cylinder head sub-assembly.


b.
A343555E01
1.892,2.193 2.077,2.348 0.185,0.155 10 *a

Apply seal packing to the No. 3 camshaft bearing cap in the areas indicated in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 mm (0.118 in.)


Text in Illustration
*a Engine Front Side
V100145

Seal Packing Application Area

NOTICE:
·

Install the No. 3 camshaft bearing cap within 3 minutes and tighten the camshaft bearing cap bolts within 15 minutes after applying seal packing.

·

Do not add engine oil within 2 hours of installation.

·

Do not start the engine for at least 2 hours after the installation.




c.

Install the No. 3 camshaft bearing cap to the cylinder head sub-assembly with the 2 camshaft bearing cap bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Wipe off excess seal packing from between No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 11310 12.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY

Hide 22815A 13.INSTALL INJECTION PUMP INSULATOR

a.

Install the injection pump insulator to the cylinder block sub-assembly.


Hide 22100 14.INSTALL SUPPLY PUMP ASSEMBLY

NOTICE:
A354097

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.


a.

Install a new O-ring to the supply pump assembly.


b.

Install the supply pump assembly to the timing chain case assembly with the 3 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Install the No. 1 fuel pump bracket to the cylinder block sub-assembly and supply pump assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 15.INSTALL NO. 1 CHAIN TENSIONER SLIPPER

a.

Install the No. 1 chain tensioner slipper to the straight pin.


Hide 13561 16.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Temporarily install the No. 1 chain vibration damper to the cylinder block sub-assembly with the bolt.


Hide 13506 17.INSTALL CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

a.
A343558E01
0.521,3.708 1.292,3.708 false 0.656,3.708 1.208,3.458 false 1.813,3.021 2.604,3.021 false 2.625,2.927 2.813,3.083 0.188,0.156 10 false *1 0.313,3.594 0.5,3.75 0.188,0.156 10 false *a 1.615,1.969 1.802,2.125 0.188,0.156 10 false *b 1.771,2.323 1.979,2.5 0.208,0.177 10 true 7°

Install the crankshaft timing sprocket to the crankshaft.

Text in Illustration
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Upper Side


b.

Align the crankshaft pulley set key as shown in the illustration.


c.
A343559E01
2.125,3.635 2.125,4.156 false 1.802,1.083 2.438,1.083 true 2.042,4.156 2.229,4.313 0.188,0.156 10 false *a 1.188,2.177 1.375,2.333 0.188,0.156 10 false *b 3.031,3.375 3.24,3.542 0.208,0.167 10 false 6° 2.49,0.99 2.719,1.219 0.229,0.229 10 true *a

Align the supply pump shaft key as shown in the illustration.

Text in Illustration
*a Supply Pump Shaft Key
*b Upper Side


d.

Remove the crankshaft timing sprocket from the crankshaft.


e.
A343560E01
1.531,0.146 2.25,0.146 true 1.531,0.563 1.698,0.563 1.698,0.563 2.333,0.208 true 2.625,0.438 3.167,0.438 true 0.354,1.563 0.896,1.563 true 0.354,1.927 0.802,1.927 true 0.5,1.927 0.5,1.74 0.5,1.74 0.719,1.74 true 0.844,1.74 1.938,1.74 true 0.885,1.854 1.771,1.854 1.771,1.854 1.771,1.74 true 0.177,1.469 0.365,1.625 0.188,0.156 10 false *1 3.219,0.354 3.406,0.51 0.188,0.156 10 false *2 0.146,1.813 0.333,1.969 0.188,0.156 10 false *a 1.354,0.042 1.542,0.198 0.188,0.156 10 false *b 1.948,1.635 2.135,1.792 0.188,0.156 10 false *c 1.344,0.458 1.531,0.615 0.188,0.156 10 false *c

Align the 2 mark plates (pink) of the No. 1 chain sub-assembly with the 2 timing marks of the crankshaft timing sprocket and install the No. 1 chain sub-assembly to the crankshaft timing sprocket as shown in the illustration.

Text in Illustration
*1 Crankshaft Timing Sprocket
*2 Injection Pump Drive Gear
*a Mark Plate (Pink)
*b Mark Plate (Yellow)
*c Timing Mark


f.

Align the mark plate (yellow) of the No. 1 chain sub-assembly with the timing mark of the injection pump drive gear and install the No. 1 chain sub-assembly to the injection pump drive gear as shown in the illustration.


g.

Install the crankshaft timing sprocket, injection pump drive gear and No. 1 chain sub-assembly to the crankshaft and supply pump shaft together.


Hide 13561 18.TIGHTEN NO. 1 CHAIN VIBRATION DAMPER

a.

Tighten the No. 1 chain vibration damper to the cylinder block sub-assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 19.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

·
A347238E01
1.704,0.281 1.889,0.436 0.185,0.155 10 *a 2.317,0.935 2.502,1.090 0.185,0.155 10 *b 1.593,1.582 1.778,1.737 0.185,0.155 10 *c 1.079,0.379 1.672,0.379 false 1.694,1.035 2.287,1.035 false 1.802,1.69 2.36,1.69 false

Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 1 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.
A343561E01
1.198,1.375 0.885,1.833 0.885,1.833 0.885,1.979 false 0.958,3.01 1.448,3.01 true 0.771,1.979 0.958,2.135 0.188,0.156 10 false *a 0.75,2.917 0.969,3.104 0.219,0.188 10 true *b

Install a new gasket and No. 1 chain tensioner assembly to the cylinder block sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*a Claw (Lower Side)
*b Groove

HINT:

Align the claw (lower side) of the gasket with the groove of the No. 1 chain tensioner assembly body to install the No. 1 chain tensioner assembly as shown in the illustration.



Hide 20.INSTALL SUPPLY PUMP SHAFT NUT

a.

Temporarily install the crankshaft pulley and crankshaft pulley set bolt to the crankshaft.


b.
A343562E01
0.079,3.762 0.264,3.917 0.185,0.155 10 *a 0.387,4.327 0.732,4.490 0.345,0.163 10 SST 0.557,3.396 0.557,4.307 false 0.764,3.662 0.764,4.142 0.764,4.142 0.556,4.142 false

Using SST, hold the crankshaft pulley and install the supply pump shaft nut to the supply pump shaft.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

If the supply pump shaft nut is tightened with torque higher than the specified torque, the No. 1 chain sub-assembly may break.



c.

Remove the crankshaft pulley set bolt and crankshaft pulley from the crankshaft.


d.
A343560E01
1.531,0.146 2.25,0.146 true 1.531,0.563 1.698,0.563 1.698,0.563 2.333,0.208 true 2.625,0.438 3.167,0.438 true 0.354,1.563 0.896,1.563 true 0.354,1.927 0.802,1.927 true 0.5,1.927 0.5,1.74 0.5,1.74 0.719,1.74 true 0.844,1.74 1.938,1.74 true 0.885,1.854 1.771,1.854 1.771,1.854 1.771,1.74 true 0.177,1.469 0.365,1.625 0.188,0.156 10 false *1 3.219,0.354 3.406,0.51 0.188,0.156 10 false *2 0.146,1.813 0.333,1.969 0.188,0.156 10 false *a 1.354,0.042 1.542,0.198 0.188,0.156 10 false *b 1.948,1.635 2.135,1.792 0.188,0.156 10 false *c 1.344,0.458 1.531,0.615 0.188,0.156 10 false *c

Make sure that the timing marks of the crankshaft timing sprocket and injection pump drive gear are aligned with the mark plates of the No. 1 chain sub-assembly as shown in the illustration.

Text in Illustration
*1 Crankshaft Timing Sprocket
*2 Injection Pump Drive Gear
*a Mark Plate (Pink)
*b Mark Plate (Yellow)
*c Timing Mark


e.

Remove the pin from the No. 1 chain tensioner assembly.


Hide 13523 21.INSTALL CAMSHAFT TIMING SPROCKET

a.
A343564E01
0.117,0.113 0.301,0.268 0.185,0.155 10 *a 1.455,0.094 1.640,0.249 0.185,0.155 10 *b 1.908,1.711 2.093,1.866 0.185,0.155 10 *c 1.654,1.358 1.839,1.512 0.185,0.155 10 *d 0.923,0.397 1.269,0.195 1.269,0.195 1.431,0.195 false 0.853,1.827 1.473,1.463 1.473,1.463 1.635,1.463 false 1.695,2.209 1.695,1.814 1.695,1.814 1.885,1.814 false

Temporarily install the 2 camshaft timing sprockets to the camshaft and No. 2 camshaft with the 2 camshaft timing sprocket bolts.

Text in Illustration
*a Engine Front Side
*b Timing Mark
*c Knock Pin
*d Cutout

NOTICE:

Make sure that the timing mark of the camshaft timing sprocket faces the front side of the engine.


HINT:

Align the knock pins of the camshaft and No. 2 camshaft with the cutout of the camshaft timing sprocket to install the camshaft timing sprocket.



b.

for Intake Side:

i.
A343565E01
2.056,0.117 2.241,0.272 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing sprocket bolt to the camshaft.

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful not to damage the camshaft or cylinder head sub-assembly with the wrench.




c.

for Exhaust Side:

i.
A343566E01
1.792,0.156 1.977,0.311 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the camshaft timing sprocket bolt to the No. 2 camshaft.

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful not to damage the No. 2 camshaft or cylinder head sub-assembly with the wrench.




Hide 13562 22.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the No. 2 chain vibration damper to the timing chain case assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13507 23.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
A343567E01
1.563,0.448 1.938,0.156 1.938,0.156 2.156,0.156 true 1.563,1.281 1.563,0.656 true 2.219,0.063 2.531,0.26 0.313,0.198 10 false *a 1.49,1.302 1.802,1.5 0.313,0.198 10 true *b

Align the mark plate (orange) of the No. 2 chain sub-assembly with the timing mark of the camshaft timing sprocket (intake side) and install the No. 2 chain sub-assembly to the camshaft timing sprocket (intake side) as shown in the illustration.

Text in Illustration
*a Mark Plate (Orange)
*b Timing Mark


b.
A343568E01
0.625,1.302 1.323,1.302 true 1.417,1.24 2.719,1.24 true 0.417,1.198 0.635,1.375 0.219,0.177 10 true *a 2.708,1.146 2.969,1.365 0.26,0.219 10 true *b

Align the mark plate (yellow) of the No. 2 chain sub-assembly with the timing mark of the injection pump drive gear and install the No. 2 chain sub-assembly to the injection pump drive gear as shown in the illustration.

Text in Illustration
*a Mark Plate (Yellow)
*b Timing Mark


c.
A343569E01
1.313,2.396 1.313,2.917 true 1.323,2.229 1.458,1.771 1.458,1.771 1.625,1.771 true 1.656,1.667 1.896,1.875 0.24,0.208 10 true *a 1.229,2.938 1.417,3.094 0.188,0.156 10 true *b

Using a wrench, turn the hexagonal portion of the No. 2 camshaft clockwise and align the mark plate (orange) of the No. 2 chain sub-assembly with the timing mark of the camshaft timing sprocket (exhaust side) to install the No. 2 chain sub-assembly to the camshaft timing sprocket (exhaust side).

Text in Illustration
*a Mark Plate (Orange)
*a Timing Mark
V100135

Turn


Hide 24.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

a.

Install the No. 2 chain tensioner slipper to the timing chain case assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13550 25.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 2 chain tensioner assembly to the timing chain case assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the No. 2 chain tensioner assembly.


Hide 27.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Make sure that the timing marks of the camshaft timing sprocket (exhaust side), camshaft timing sprocket (intake side), injection pump drive gear and crankshaft timing sprocket are at the positions shown in the illustration.

A456073C01
1.406,0.677 1.99,0.917 1.99,0.917 2.177,0.917 true 1.406,0.542 1.698,0.292 1.698,0.292 1.875,0.292 true 4.031,0.542 4.323,0.292 4.323,0.292 4.5,0.292 true 4.01,0.677 4.594,0.917 4.594,0.917 4.781,0.917 true 5.396,3.104 5,3.198 5,3.198 4.885,3.198 true 4.875,3.688 5.365,3.688 true 5.5,3.104 6.313,2.938 6.313,2.938 6.521,2.938 true 5.469,3.635 6.292,4.063 6.292,4.063 6.5,4.063 true 5.302,6.25 5,6.469 5,6.469 4.865,6.469 true 5.198,6 5.01,6.458 true 5.375,5.896 6.188,5.281 6.188,5.281 6.396,5.281 true 0.375,0.198 0.688,0.354 0.313,0.156 10 false *a 2.948,0.198 3.26,0.354 0.313,0.156 10 false *b 4.729,2.552 5.042,2.708 0.313,0.156 10 false *c 4.719,4.813 5.031,4.969 0.313,0.156 10 false *d 4.74,3.104 4.917,3.26 0.177,0.156 10 false *f 4.688,6.354 4.917,6.563 0.229,0.208 10 false *g 2.208,0.823 2.521,0.979 0.313,0.156 10 false *h 1.906,0.208 2.219,0.365 0.313,0.156 10 false *e 4.531,0.198 4.844,0.354 0.313,0.156 10 false *e 4.823,0.833 5.135,0.99 0.313,0.156 10 false *h 5.302,2.49 5.813,2.677 0.51,0.188 10 false 36.2° 4.75,5.125 5.26,5.313 0.51,0.188 10 false 100° 4.729,3.594 4.906,3.75 0.177,0.156 10 false *f 6.552,2.844 6.865,3 0.313,0.156 10 false *h 6.531,3.969 6.844,4.125 0.313,0.156 10 false *h 6.427,5.188 6.74,5.344 0.313,0.156 10 false *h
*a Camshaft Timing Sprocket (Exhaust Side) *b Camshaft Timing Sprocket (Intake Side)
*c Injection Pump Drive Gear *d Crankshaft Timing Sprocket
*e Mark Plate (Orange) *f Mark Plate (Yellow)
*g Mark Plate (Pink) *h Timing Mark



Hide 13620B 28.INSTALL ENGINE BALANCER ASSEMBLY

a.

Set the engine balancer assembly to the cylinder block sub-assembly.


b.
A354061E01
0.74,0.708 0.906,0.875 0.167,0.167 10 false B 0.125,0.083 0.313,0.24 0.188,0.156 10 false *a 0.125,2.458 0.313,2.615 0.188,0.156 10 false *b 0.396,1.021 0.563,1.188 0.167,0.167 10 false A 1.042,2.74 1.208,2.906 0.167,0.167 10 false 1 0.708,3.094 0.875,3.26 0.167,0.167 10 false 4 1.375,2.385 1.542,2.552 0.167,0.167 10 false 5 0.375,3.417 0.542,3.583 0.167,0.167 10 false 8 1.75,1.771 1.938,1.958 0.188,0.188 10 true A 1.073,0.354 1.24,0.521 0.167,0.167 10 false B 1.385,0 1.552,0.167 0.167,0.167 10 false B 2.76,0.594 2.927,0.781 0.167,0.188 10 true B 2.438,1.094 2.604,1.26 0.167,0.167 10 true B 2.104,1.438 2.271,1.604 0.167,0.167 10 true B 2.771,2.99 2.938,3.198 0.167,0.208 10 true 6 2.438,3.479 2.604,3.646 0.167,0.167 10 true 2 2.104,3.823 2.271,3.99 0.167,0.167 10 true 3 1.75,4.167 1.917,4.333 0.167,0.167 10 true 7

Install the engine balancer assembly to the cylinder block sub-assembly with the 8 bolts and tighten the bolts in the sequence shown in the illustration.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 43 N*m (438 kgf*cm, 32 ft.*lbf)

Bolt Length:
Item Specified Condition
Bolt A 50 mm (1.97 in.)
Bolt B 55 mm (2.17 in.)


Text in Illustration
*a Bolt Type
*b Tightening Order


Hide 13639 29.INSTALL BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY

HINT:
A354098E01
0.313,0.458 1,0.458 true 1.125,2.344 1.344,2.344 1.344,2.344 1.927,1.781 true 1.333,2.344 1.688,1.792 true 0.531,3.063 1.781,3.063 true 0.51,0.458 0.51,0.677 0.51,0.677 1,0.677 true 0.76,3.063 0.76,3.417 0.76,3.417 1.771,3.417 true 0.135,0.354 0.448,0.552 0.313,0.198 10 false *a 0.938,2.24 1.25,2.438 0.313,0.198 10 false *b 0.354,2.958 0.667,3.156 0.313,0.198 10 false *a

Before installing the balance shaft gear sub-assembly, make sure to confirm the positions of the timing marks and paint marks (pink).


Text in Illustration
*a Timing Mark
*b Paint Mark (Pink)

a.
A347359E01
3.079,0.517 3.264,0.672 0.185,0.155 10 *1 2.122,1.544 2.307,1.698 0.185,0.155 10 *2 1.105,0.012 1.290,0.166 0.185,0.155 10 *a 2.716,0.124 2.901,0.279 0.185,0.155 10 *b 2.037,1.939 2.222,2.094 0.185,0.155 10 *a 0.235,1.856 0.420,2.011 0.185,0.155 10 *a 0.51,1.107 0.695,1.262 0.185,0.155 10 *b 1.313,0.125 1.947,0.125 false 2.064,0.222 2.698,0.222 false 2.421,0.609 3.055,0.609 false 1.465,1.636 2.099,1.636 false 1.374,2.039 2.009,2.039 false 0.445,1.967 1.028,1.967 false 0.714,1.21 0.895,1.21 0.895,1.21 1.281,1.927 false 0.892,1.212 1.154,1.89 false

Align the mark plate (yellow) of the No. 3 chain sub-assembly with the timing mark of the balance shaft timing sprocket and install the No. 3 chain sub-assembly to the balance shaft timing sprocket as shown in the illustration.

Text in Illustration
*1 Balance Shaft Timing Sprocket
*2 Balance Shaft Gear Sub-assembly
*a Mark Plate (Yellow)
*b Timing Mark

NOTICE:

Make sure that the timing plate of the No. 3 chain sub-assembly faces the front side of the engine.



b.

Align the 2 mark plates (yellow) of the No. 3 chain sub-assembly with the 2 timing marks of the balance shaft timing gear sub-assembly and install the No. 3 chain sub-assembly to the balance shaft timing gear sub-assembly as shown in the illustration.


c.
A347358

Apply engine oil to the position shown in the illustration.


d.
A347360E01
1.802,3.5 1.802,4.229 true 1.698,3.427 1.344,4.25 1.344,4.25 1.188,4.25 true 0.75,3.458 1.49,3.458 true 1.76,3.26 2.573,2.875 2.573,2.875 2.719,2.875 true 1.74,4.229 1.927,4.385 0.188,0.156 10 false *a 0.563,3.365 0.75,3.521 0.188,0.156 10 true *b 2.76,2.792 2.948,2.948 0.188,0.156 10 false *c 1.01,4.146 1.198,4.302 0.188,0.156 10 false *c

Align the timing mark of the engine balancer assembly with the 2 paint marks (pink) and timing mark of the balance shaft gear sub-assembly, and then install the balance shaft timing sprocket, balance shaft gear sub-assembly with No. 3 chain sub-assembly to the crankshaft and engine balancer assembly as shown in the illustration.

Text in Illustration
*a Timing Mark (Engine Balancer Assembly Side)
*b Timing Mark (Balance Shaft Gear Sub-assembly Side)
*c Paint Mark (Pink)
(Balance Shaft Gear Sub-assembly Side)


e.
A347359E01
3.079,0.517 3.264,0.672 0.185,0.155 10 *1 2.122,1.544 2.307,1.698 0.185,0.155 10 *2 1.105,0.012 1.290,0.166 0.185,0.155 10 *a 2.716,0.124 2.901,0.279 0.185,0.155 10 *b 2.037,1.939 2.222,2.094 0.185,0.155 10 *a 0.235,1.856 0.420,2.011 0.185,0.155 10 *a 0.51,1.107 0.695,1.262 0.185,0.155 10 *b 1.313,0.125 1.947,0.125 false 2.064,0.222 2.698,0.222 false 2.421,0.609 3.055,0.609 false 1.465,1.636 2.099,1.636 false 1.374,2.039 2.009,2.039 false 0.445,1.967 1.028,1.967 false 0.714,1.21 0.895,1.21 0.895,1.21 1.281,1.927 false 0.892,1.212 1.154,1.89 false

Make sure that the timing marks of the balance shaft timing sprocket and balance shaft gear sub-assembly are aligned with the mark plates of the No. 3 chain sub-assembly as shown in the illustration.

Text in Illustration
*1 Balance Shaft Timing Sprocket
*2 Balance Shaft Gear Sub-assembly
*a Mark Plate (Yellow)
*b Timing Mark


Hide 11991A 30.INSTALL NO. 1 BALANCE SHAFT THRUST PLATE

a.

Apply engine oil to the front and rear surfaces of the No. 1 balance shaft thrust plate.


b.

Install the No. 1 balance shaft thrust plate to the crankshaft with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13560A 31.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 3 chain tensioner assembly, the plunger and 2 springs may come off of the No. 3 chain tensioner assembly body, but this is not a malfunction.

·
A347346E01
0.554,1.812 0.739,1.967 0.185,0.155 10 *a 1.372,1.682 1.557,1.837 0.185,0.155 10 *b 2.942,1.784 3.127,1.939 0.185,0.155 10 *c 0.667,1.277 0.667,1.814 false 1.457,1.127 1.457,1.664 false 2.368,1.397 2.552,1.551 0.185,0.155 10 *b 2.453,0.842 2.453,1.379 false 3.051,1.323 3.051,1.78 false

Before installing the plunger and 2 springs to the No. 3 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 3 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.

Install the No. 3 chain tensioner assembly to the engine balancer assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the No. 3 chain tensioner assembly.


Hide 15133B 33.INSTALL OIL PUMP RELIEF VALVE PLUG

a.

Install a new gasket and oil pump relief valve plug to the timing chain cover sub-assembly.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 11302 35.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11381 37.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Clean and degrease the contact surfaces of the rear engine oil seal retainer and cylinder block sub-assembly.


b.
A343573E01
0.08,0.867 0.265,1.021 0.185,0.155 10 *a 0.288,0.978 0.89,0.978 false

Apply seal packing to the rear engine oil seal retainer in the areas indicated in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*a Seal Packing

NOTICE:
·

Remove any engine oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil within 2 hours of installation.

·

Do not start the engine for at least 2 hours after the installation.




c.

Install the rear engine oil seal retainer to the cylinder block sub-assembly, and then install the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15104 39.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A347345E01
1.354,0.313 1.49,0.469 0.135,0.156 10 false 3 2.313,0.521 2.5,0.719 0.188,0.198 10 true 4 1.229,0.688 1.365,0.844 0.135,0.156 10 true 5 1.813,1.354 1.979,1.552 0.167,0.198 10 true 2 0.99,1.615 1.125,1.771 0.135,0.156 10 true 1

Install a new gasket and oil strainer sub-assembly to the cylinder block sub-assembly with the 5 bolts in several steps in the sequence shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the oil strainer sub-assembly.



Hide 12102A 41.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 44.INSTALL CRANKSHAFT POSITION SENSOR HARNESS BRACKET

a.

Install the crankshaft position sensor harness bracket to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the crankshaft position sensor connector.


Hide 12581A 45.INSTALL NO. 1 CYLINDER BLOCK INSULATOR

a.

Install the No. 1 cylinder block insulator to the cylinder block sub-assembly.


Hide 12585 46.INSTALL NO. 5 CYLINDER BLOCK INSULATOR

a.

Install the No. 5 cylinder block insulator to the cylinder block sub-assembly.


Hide 11201 47.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12108A 48.INSTALL OIL FILLER CAP GASKET

a.

Install the oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 49.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 23670 51.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 23760 52.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 15677 53.INSTALL OIL FILTER BRACKET

a.

Install 2 new O-rings to the cylinder block sub-assembly.


b.

Install the oil filter bracket to the cylinder block sub-assembly with the 2 nuts and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 15600A 54.INSTALL OIL FILTER UNION

a.

Using a 27 mm deep socket wrench, install the oil filter union to the oil filter bracket.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 83530 57.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 12311 58.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 12501 61.INSTALL GENERATOR BRACKET SUB-ASSEMBLY

a.

Install the generator bracket sub-assembly to the cylinder head sub-assembly and timing chain case assembly with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12583A 62.INSTALL NO. 3 CYLINDER BLOCK INSULATOR

a.

Install the No. 3 cylinder block insulator to the cylinder block sub-assembly.


Hide 63.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


Hide 12582 64.INSTALL NO. 2 CYLINDER BLOCK INSULATOR

a.

Install the No. 2 cylinder block insulator to the front No. 1 engine mounting bracket LH.


Hide 12281A 65.INSTALL NO. 1 ENGINE HANGER

a.

Install the No. 1 engine hanger to the cylinder head sub-assembly with the 2 bolts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 11382C 66.INSTALL CAMSHAFT OIL SEAL RETAINER

NOTICE:

If the camshaft oil seal retainer is dropped, replace it with a new one.


a.

Before installing a new camshaft oil seal retainer, clean the installation surface of the No. 3 camshaft bearing cap and cylinder head sub-assembly and remove any foreign matter.


b.
A343512E01
3.06,0.344 3.245,0.499 0.185,0.155 10 *1 2.58,2.967 2.764,3.122 0.185,0.155 10 *a 0.504,1.042 0.870,1.205 0.366,0.163 10 SST 2.856,0.071 3.222,0.233 0.366,0.163 10 SST 2.812,0.893 2.812,0.442 2.812,0.442 3.025,0.442 false 2.596,0.765 2.596,0.153 2.596,0.153 2.808,0.153 false 1.348,2.262 1.107,1.135 1.107,1.135 0.895,1.135 false

Using SST and a hammer, tap in a new camshaft oil seal retainer to the No. 3 camshaft bearing cap and cylinder head sub-assembly as shown in the illustration.

SST
09223-46011  

Standard depth:

0 to 0.8 mm (0 to 0.0315 in.)


Text in Illustration
*1 Camshaft Oil Seal Retainer
*a Depth


Hide 29300 67.INSTALL VACUUM PUMP ASSEMBLY

a.
A343513

Coat 2 new O-rings with engine oil, and install them to the vacuum pump assembly.


b.
A343514E02
1.198,1.292 1.198,1.823 true 2.292,0.865 2.406,0.417 2.406,0.417 2.583,0.417 true 1.156,1.833 1.323,1.99 0.167,0.156 10 true A 2.635,0.333 2.802,0.49 0.167,0.156 10 true B

Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly labeled A and the groove of the No. 2 camshaft labeled B can engage.


c.

Install the vacuum pump assembly to the cylinder head sub-assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)