Home › Engine / Hybrid System › 2TR-FE (FUEL) › FUEL TANK (for 5 Door) › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053666 2TR-FE FUEL _0260534 FUEL TANK(for 5 Door) A

2TR-FE FUEL  FUEL TANK(for 5 Door)  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE REAR SEAT ASSEMBLY LH

Hide 58371F 5.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 67934 6.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

Hide 67918D 7.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58325E 8.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A220797

Remove the 3 screws and rear floor service hole cover.


b.
A220800E01
0.038,0.031 0.301,0.195 0.263,0.164 12 *A 0.038,2.311 0.302,2.482 0.264,0.171 12 *B

Disconnect the fuel pump and sender gauge connector.

Text in Illustration
*A for Single Tank Type
*B for Double Tank Type


Hide 77606 9.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A220805

Remove the 6 bolts and No. 1 fuel tank protector sub-assembly.


Hide 77209D 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A220806

Disconnect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 11.DRAIN FUEL

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Operate the fuel pump and drain the fuel from the fuel tank main tube.

CAUTION:
·

Do not smoke or be near an open flame when working on the fuel system.

·

Secure good ventilation.

·

Keep gasoline away from rubber or leather parts.




Hide 77207A 12.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY

a.
A223269

Disconnect the fuel return tube sub-assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 13.DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)

a.
A220810

Disconnect the fuel cut off tube (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 14.DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)

a.
A220809

Disconnect the fuel cut off tube (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77012 15.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223270

Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77012 16.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223275

Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77206C 17.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223276

Disconnect the No. 2 fuel main tube sub-assembly (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77213B 18.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A220811

Disconnect the fuel tank to filler pipe hose from the filler pipe.


Hide 77100U 19.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place an engine lifter under the fuel tank sub-assembly.


b.
A220832

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank band sub-assemblies.


c.

Slowly lower the engine lifter slightly.


Hide 77651A 20.REMOVE FUEL TANK CUSHION

a.
A220812E01
0.679,0.225 0.863,0.368 0.184,0.143 10 *1 0.886,0.313 0.976,0.313 0.976,0.313 1.176,0.849 false 2.253,0.177 2.437,0.320 0.184,0.143 10 *2 2.46,0.265 2.55,0.265 2.55,0.265 2.75,0.801 false 2.05,1.934 2.234,2.076 0.184,0.143 10 *3 2.257,2.018 2.347,2.018 2.347,2.018 2.547,1.677 false

Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.

Text in Illustration
*1 No. 1 Fuel Tank Cushion
*2 No. 2 Fuel Tank Cushion
*3 No. 3 Fuel Tank Cushion


Hide 77209D 21.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A220814E02
2.369,2.868 2.555,3.017 0.185,0.149 10 *b 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *a 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *c 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *d 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 2 fuel tube joint clips and pull out the fuel tank main tube sub-assembly and fuel return tube sub-assembly.

Text in Illustration
*a Fuel Tube
*b Fuel Tube Joint
*c Fuel Tube Joint Clip
*d O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A220818

Remove the fuel tank main tube sub-assembly and fuel return tube sub-assembly from the fuel tank sub-assembly.


Hide 77209D 22.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A220813E03
2.333,2.958 2.24,2.958 2.24,2.958 2.042,3.26 false 1.167,2.958 1.271,2.958 1.271,2.958 1.458,3.25 false 2.542,3.292 2.438,3.292 2.438,3.292 2.25,3.583 false 1.719,3.927 1.188,3.927 false 1.719,3.813 1.292,3.813 1.292,3.813 1.292,3.927 false 2.365,2.875 2.583,3.073 0.219,0.198 10 false *b 0.958,2.865 1.208,3.063 0.25,0.198 10 false *a 2.573,3.198 2.792,3.406 0.219,0.208 10 false *c 0.969,3.844 1.208,4.031 0.24,0.188 10 false *d

Remove the 3 fuel tube joint clips and pull out the fuel tank main tube sub-assembly, fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly.

Text in Illustration
*a Fuel Tube
*b Fuel Tube Joint
*c Fuel Tube Joint Clip
*d O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A220817

Detach the clamp and remove the No. 2 fuel main tube sub-assembly from the fuel tank sub-assembly.


c.

Remove the fuel tank main tube sub-assembly and fuel return tube sub-assembly from the fuel tank sub-assembly.


Hide 77020A 23.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77643A 24.REMOVE NO. 3 FUEL TANK PROTECTOR

a.
A220823

Remove the 2 bolts.


b.

Detach the 4 clamps and remove the No. 3 fuel tank protector.


Hide 77213B 25.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A220822

Remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.