Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for 5 Door) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053741 INTERIOR PANELS / TRIM _0261217 ROOF HEADLINING(for 5 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 5 Door)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

a.

for Manual Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)>REMOVAL).


b.

for Power Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>REMOVAL).


c.

for Face to Face Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>REMOVAL).


Hide 4.REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)

a.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Remove the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>REMOVAL).


b.

for 60/40 Split Slide Walk-in Seat Type RH Side:

Remove the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type RH Side)>REMOVAL).


Hide 5.REMOVE REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)

a.

for 60/40 Split Double-folding Seat Type LH Side:

Remove the rear No. 1 seatback assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>REMOVAL).


b.

for 60/40 Split Double-folding Seat Type RH Side:

Remove the rear No. 1 seatback assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side)>REMOVAL).


Hide 67920 6.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B238732E07
0.208,1.104 0.49,1.354 0.281,0.25 0.417,1.229 0.49,1.229 false 0.49,1.229 0.635,1.188 false 2.021,2.396 2.885,2.031 2.885,2.031 3.073,2.031 true 0.24,1.135 0.438,1.323 0.198,0.188 10 false *1 3.104,1.948 3.302,2.135 0.198,0.188 10 true *1

a.

Put protective tape around the door scuff plate.


b.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 67910 7.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

B238734

a.

Remove the clip.


b.

Detach the clip and claw and remove the cowl side trim board.


Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B238778

a.

Remove the front door opening trim weatherstrip.


Hide 62311B 11.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74616C 12.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

B238741E02
0.802,1.49 0.958,1.49 0.958,1.49 1.635,1.177 true 0.615,1.396 0.813,1.583 0.198,0.188 10 false *1

HINT:

Use the same procedure for the other front No. 1 assist grip plug.


a.

Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74615E 13.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 74611F 14.REMOVE NO. 1 ASSIST GRIP

B238742

HINT:

Use the same procedure for the other No. 1 assist grip.


a.

Remove the 2 bolts.


b.

Detach the 2 claws and remove the No. 1 assist grip.


Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

B238743

a.

Detach the 3 guides and remove the front pillar garnish.


b.
B238744E02
1.115,0.74 0.719,1.25 0.719,1.25 0.594,1.25 true 1.854,0.729 2.25,0.354 2.25,0.354 2.052,0.354 false 2.031,1.344 2.813,0.854 2.813,0.854 2.604,0.854 true 0.406,1.167 0.625,1.354 0.219,0.188 10 false *1 1.875,0.271 2.094,0.458 0.219,0.188 10 false *2 2.417,0.76 2.635,0.948 0.219,0.188 10 false *3

w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly.

i.

Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


Text in Illustration
*1 Curtain Shield Airbag Assembly
*2 Adhesive Tape
*3 Protective Cover



Hide 62211 16.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 58371F 17.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

B238730E05
1.646,1.26 2.042,1.51 false 2.042,1.51 2.146,1.51 false 2.146,1.417 2.333,1.583 0.188,0.167 10 true *1

HINT:

Use the same procedure for all rear No. 1 floor step covers.


a.

Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 67934 18.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

B238731

a.

Remove the 2 bolts and quarter scuff plate.


Hide 67933 19.REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 67918D 20.REMOVE REAR DOOR SCUFF PLATE LH

B238733E02
1.74,2.375 2.063,3.135 2.063,3.135 2.125,3.135 true 1.74,2.229 0.688,3.01 0.688,3.01 0.552,3.01 true 0.385,2.917 0.583,3.094 0.198,0.177 10 false *1 2.146,3.052 2.344,3.229 0.198,0.177 10 false *1

a.

Put protective tape around the rear door scuff plate.


b.

Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 67917C 21.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62332C 22.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B238780

a.

Remove the rear door opening trim weatherstrip.


Hide 62331C 23.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 73233 24.REMOVE OUTER LAP BELT ANCHOR COVER

B238735

HINT:

Use the same procedure for the other outer lap belt anchor cover.


a.

Detach the 3 claws and remove the outer lap belt anchor cover.


Hide 62414A 25.REMOVE LOWER CENTER PILLAR GARNISH LH

B238736

a.

Remove the bolt and disconnect the front seat outer belt floor anchor.


b.
B238737

Detach the 4 claws and 2 clips and remove the lower center pillar garnish.


Hide 62413A 26.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 74638 27.REMOVE NO. 2 ASSIST GRIP PLUG LH

B238739E04
1.583,1.25 2.104,1.521 2.104,1.521 2.24,1.521 true 2.26,1.438 2.531,1.667 0.271,0.229 10 false *1

HINT:

Use the same procedure for the other front No. 2 assist grip plug.


a.

Using a screwdriver, detach the 2 claws and remove the front No. 2 assist grip plug.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74637 28.REMOVE NO. 2 ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 74611G 29.REMOVE NO. 2 ASSIST GRIP

B238740

HINT:

Use the same procedure for the other No. 2 assist grip.


a.

Remove the 2 bolts.


b.

Detach the 2 claws and remove the No. 2 assist grip.


Hide 62412 30.REMOVE CENTER PILLAR GARNISH LH

B238738

a.

Move the front shoulder belt anchor adjuster to the lowest position.


b.

Remove the bolt.


c.

Detach the 2 clips and 2 guides.


d.

Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.


Hide 62411 31.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 64910M 32.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.

Remove the tonneau cover.


Hide 64717A 33.REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

B240044

HINT:

Use the same procedure for the other front luggage compartment trim cover.


a.

Detach the 4 claws and remove the cap.


b.
B238749E02
1.365,0.885 0.719,0.469 0.719,0.469 0.531,0.469 true 0.365,0.375 0.583,0.615 0.219,0.24 10 false *1

Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker


Hide 58401A 34.REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

B238750

a.

Detach the clip and remove the No. 1 deck board.


Hide 58574A 35.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

B238748

a.

Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.


Hide 57412C 36.REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

B238764

a.

Remove the 3 bolts and floor side rail.


Hide 57411D 37.REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

HINT:

Use the same procedure described for the LH side.


Hide 58570C 38.REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

a.

Detach the 4 claws and remove the rear floor carpet.

B238751E01
3.283,0 3.655,0.305 0.371,0.305 10 *B 1.021,0 1.392,0.305 0.371,0.305 10 *A 5.581,0 5.952,0.305 0.371,0.305 10 *C

Text in Illustration
*A w/o Deck Rail *B w/ Deck Rail
*C for Face to Face Seat Type - -


Hide 73233A 39.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

B238752

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


a.

Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.


Hide 64725D 40.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook.


a.

Remove the luggage compartment trim hook by turning it clockwise.


Hide 64937A 41.REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

B238754E01
0.675,1.631 0.877,1.834 0.202,0.202 10 *1 0.853,1.723 0.96,1.723 false 0.96,1.723 1.693,1.231 false

HINT:

Use the same procedure for the other No. 1 tonneau cover holder cap.


a.

Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 64712F 42.REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

B240051E01
2.331,1.703 2.612,1.873 0.281,0.170 10 *1 1.619,1.453 2.163,1.81 false 2.163,1.81 2.331,1.81 false

HINT:

Use the same procedure for the other front deck side trim cover.


a.

Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74617A 43.REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

B238757E01
2.669,1.512 2.923,1.741 0.254,0.229 10 *1 1.504,1.287 2.52,1.608 false 2.52,1.608 2.662,1.608 false

HINT:

Use the same procedure for all assist grip plugs.


a.

Using a screwdriver, detach the 2 claws and remove the assist grip plug.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74603C 44.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

B238758

HINT:

Use the same procedure for the other assist grip.


a.

Remove the 2 bolts and assist grip.


Hide 64740C 45.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.
B238753

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B238756

Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.


iii.

Remove the 4 bolts and 2 screws.


iv.

Detach the 5 clips and 8 claws.


v.

Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

B238755



b.

w/ Rear No. 2 Seat:

i.
B238753

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B238759

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 2 bolts and 2 screws.


iv.

Detach the 4 clips and 8 claws and remove the deck trim side panel.

B238760



Hide 64730B 46.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat:

i.
B238821

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B238823

Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.


iii.

Remove the 4 bolts and screws.


iv.

Detach the 5 clips and 8 claws.


v.

Disconnect each connector.


vi.

Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

B238822



b.

w/ Rear No. 2 Seat:

i.
B238821

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B238826

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 2 bolts and screw.


iv.

Detach the 4 clips and 8 claws.


v.

Disconnect each connector and remove the deck trim side panel.

B238827



Hide 62520P 47.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B238745

a.

Move the rear shoulder belt anchor adjuster to the lowest position.


b.

Detach the 2 clips and 2 guides.


c.

Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.


Hide 62510P 48.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62640P 49.REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

B238746

a.

w/o Rear No. 2 Seat:

i.

Detach the 7 clips and 2 guides and remove the rear quarter trim panel.



b.
B241336

w/ Rear No. 2 Seat:

i.

Detach the 7 clips and 2 guides.


ii.
B238747

Detach the 4 clips and 2 guides, pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.



Hide 62630P 50.REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74610A 51.REMOVE ASSIST GRIP SUB-ASSEMBLY

B184001E03
1.646,0.5 1.854,0.125 false 1.854,0.125 2.427,0.125 false 2.469,0.031 2.938,0.438 0.469,0.406 10 false *1

HINT:

Use the same procedure for the other assist grip.


a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

Detach the 2 clips and remove the assist grip.


c.

Remove the 2 clips from the vehicle body.


Hide 74610U 52.REMOVE REAR ASSIST GRIP ASSEMBLY LH

B184002E03
1.684,0.499 1.822,0.211 false 1.822,0.211 2.398,0.211 false 2.436,0.112 2.752,0.351 0.316,0.239 10 *1

a.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

Detach the 2 clips and remove the assist grip.


c.

Remove the 2 clips from the vehicle body.


Hide 74610V 53.REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74611B 54.REMOVE ASSIST GRIP (w/ Rear No. 2 Seat)

B238761E03
0.604,1.792 0.76,1.792 0.76,1.792 1.115,1.323 false 0.438,1.698 0.719,1.917 0.281,0.219 10 false *1

HINT:

Use the same procedure for the other assist grip.


a.

Using a screwdriver, detach the 4 claws and open the 2 covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.
B238762

Remove the 2 bolts and assist grip.


Hide 74318 55.REMOVE VISOR BRACKET COVER LH

B181706

HINT:

Use the same procedure for the other visor bracket cover.


a.

Detach the 4 claws and remove the visor bracket cover.


Hide 74317 56.REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 74320 57.REMOVE VISOR ASSEMBLY LH

B181707

a.

Remove the 2 screws and visor.


Hide 74310 58.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 59.REMOVE VISOR HOLDER

B151362E02
0.781,0.361 1.312,0.642 0.531,0.281 10 45°

HINT:

Use the same procedure for the other visor holder.


a.

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Detach the 2 claws and remove the visor holder.


Hide 89943 61.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 87834 62.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 81240 63.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

a.

Remove the No. 1 room light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Center)>REMOVAL).


Hide 81240D 64.REMOVE NO. 2 ROOM LIGHT ASSEMBLY

a.

Remove the No. 2 room light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Rear)>REMOVAL).


Hide 86295 65.REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

Hide 87217D 66.REMOVE REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)

Hide 86160T 67.REMOVE REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)

Hide 63310 68.REMOVE ROOF HEADLINING ASSEMBLY

B268455

a.

w/ EC Mirror:

Disconnect the inner mirror connector.


b.
E197773

w/ Rain Sensor:

Disconnect the rain sensor connector.


c.
B238774

w/ Sliding Roof:

Disconnect the drive gear connector.


d.
B358962

w/ Digital Audio Broadcasting Antenna:

Disconnect the connector and detach the wire harness clamp.


e.
B238771

Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.


f.
B238770

Remove the bolt.


g.

Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.


h.
B238773

Disconnect the 2 connectors and detach the clamp from the rear pillar LH.


i.
B357792

Disconnect the connector and detach the 3 clamps from the rear pillar RH.


j.
B238775

w/ Rear Seat Entertainment System:

Disconnect the 2 connectors.


k.
B238765

w/o Sliding Roof:

i.

Detach the 2 clips.



l.
B238767E03
0.948,2.292 0.958,2.75 0.958,2.75 1.208,2.302 true 0.948,1.021 0.958,0.49 0.958,0.49 1.188,1.021 true 1.438,1.51 1.854,1.625 false 1.427,1.771 1.854,1.625 false 1.438,1.292 1.854,1.635 false 1.427,2.021 1.854,1.635 false 0.573,2.083 0.156,2.75 0.156,2.75 0.281,2.75 true 0.563,1.229 0.198,0.531 0.198,0.531 0.344,0.531 true 0.313,2.677 0.521,2.875 0.208,0.198 10 false *1 0.875,2.75 1.083,2.948 0.208,0.198 10 false *2 0.375,0.458 0.583,0.656 0.208,0.198 10 false *1 0.844,0.313 1.052,0.51 0.208,0.198 10 false *2 1.854,1.552 2.063,1.75 0.208,0.198 10 true *2

w/ Sliding Roof:

i.

Detach the 2 clips, 2 guides and 8 fasteners.

Text in Illustration
*1 Guide
*2 Fastener



m.
B238766E03
0.948,2.26 0.948,2.74 0.948,2.74 1.208,2.313 true 0.948,1.021 0.958,0.458 0.958,0.458 1.229,1.031 true 1.427,1.99 1.813,1.604 1.813,1.604 1.406,1.313 true 0.573,2.083 0.146,2.771 0.146,2.771 0.26,2.771 false 0.563,1.24 0.208,0.563 0.208,0.563 0.365,0.563 true 0.271,2.677 0.427,2.854 0.156,0.177 10 false *1 0.865,2.75 1.021,2.927 0.156,0.177 10 false *2 0.406,0.479 0.563,0.656 0.156,0.177 10 false *1 0.875,0.281 1.031,0.458 0.156,0.177 10 false *2 1.854,1.531 2.01,1.708 0.156,0.177 10 true *2

w/ Rear Seat Entertainment System:

i.

Detach the 2 clips, 2 guides and 6 fasteners.

Text in Illustration
*1 Guide
*2 Fastener



n.
B238777

Remove the roof headlining from the back door as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when removing it.



Hide 73024 69.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B238795

a.

Detach the 5 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.


Hide 73023 70.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73034 71.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B238794

a.

Detach the 6 claws of the rear shoulder belt anchor plate and slide the rear shoulder belt anchor plate in the direction of the arrow to remove it.


Hide 73033 72.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62432B 73.REMOVE NO. 1 ROOF SIDE RAIL GARNISH LH

a.
B238768E01
1.506,1.514 1.776,1.739 0.270,0.225 10 *a 2.162,1.072 1.849,1.608 false 1.849,1.608 1.682,1.608 false

Detach the 3 clips.


b.

Cut off the 3 clips and remove the roof side rail garnish.

Text in Illustration
*1 Cut Off Position


c.

Remove 3 clips from the vehicle body.


Hide 62431B 74.REMOVE NO. 1 ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62477A 75.REMOVE ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)

B238799

a.

Detach the 4 claws and 2 guides and remove the roof side inner garnish cap.


Hide 62476A 76.REMOVE ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 73372 77.REMOVE REAR SEAT SHOULDER BELT HANGER LH

B238782

a.

Detach the claw and guide and remove the rear seat shoulder belt hanger.


Hide 73371 78.REMOVE REAR SEAT SHOULDER BELT HANGER RH

HINT:

Use the same procedure described for the LH side.


Hide 62627B 79.REMOVE QUARTER TRIM COVER

B238798

HINT:

Use the same procedure for the other quarter trim cover.


a.

Detach the 2 claws and remove the quarter trim cover.


Hide 64766B 80.REMOVE QUARTER TRIM JACK COVER

B238797

a.

Detach the 3 claws and 2 guides and remove the quarter trim jack cover.


Hide 64715C 81.REMOVE DECK SIDE TRIM COVER LH

B238796

a.

Detach the 3 claws and 2 guides and remove the deck side trim cover.


Hide 66424 82.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

B238783

a.

Detach the 2 claws and remove the rear side rail spacer.


Hide 66414A 83.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66425A 84.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

B238784

a.

Detach the 2 claws and remove the rear No. 2 side rail spacer.


Hide 66415A 85.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66426B 86.REMOVE REAR NO. 3 SIDE RAIL SPACER LH

B238785

a.

Detach the 2 claws and remove the rear No. 3 side rail spacer.


Hide 66416 87.REMOVE REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.