Home › Engine / Hybrid System › 2TR-FE (FUEL) › FUEL TANK (for 3 Door) › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053666 2TR-FE FUEL _0260535 FUEL TANK(for 3 Door) A

2TR-FE FUEL  FUEL TANK(for 3 Door)  INSTALLATION  


PROCEDURE

Hide 77651A 1.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install new 2 No. 1 fuel tank cushions to the fuel tank sub-assembly.


Hide 77295C 2.INSTALL FUEL TUBE GROMMET

a.

Attach the clamp to install the fuel tube grommet.


Hide 77011 3.INSTALL FUEL TANK FILLER PIPE LOWER SUB-ASSEMBLY

a.

Install a new gasket and the fuel tank filler pipe lower sub-assembly with the 8 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 77269A 4.INSTALL FUEL TANK BREATHER HOSE

a.

Install the fuel tank breather hose to the fuel tank sub-assembly.


Hide 77213B 5.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank sub-assembly.


Hide 83320 6.INSTALL FUEL SENDER GAUGE ASSEMBLY

a.

Install a new gasket and the fuel sender gauge assembly with the 5 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



Hide 77380 7.INSTALL FUEL CUT OFF VALVE ASSEMBLY

a.

Install the fuel cut off valve assembly to the fuel tank sub-assembly.


Hide 77026B 8.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Install a new gasket and the No. 1 fuel evaporation tube sub-assembly with the 4 screws and attach the clamp.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 77100U 10.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank sub-assembly on an engine lifter and lift up the engine lifter.


b.

Install the 2 fuel tank band sub-assemblies with the 2 pins and 2 clips.


c.

Connect the 2 fuel tank band sub-assemblies with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 77269A 11.CONNECT FUEL TANK BREATHER HOSE

a.

Connect the fuel tank breather hose to the filler pipe.


Hide 77213B 12.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the filler pipe.


Hide 13.CONNECT FUEL HOSE

a.

Connect the fuel evaporation hose and fuel hose.


Hide 77251B 14.CONNECT FUEL MAIN TUBE

a.

Connect the fuel main tube (See page Engine / Hybrid System>2TR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77606 15.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly with the 5 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 58325E 16.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel sender gauge connector and fuel pump connector.


b.

Install the rear floor service hole cover with the 3 screws.


Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).