Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
64714C
1.INSTALL DECK SIDE TRIM COVER RH (w/o Spare Tire)
Attach the 7 claws and 3 guides to install the deck side trim cover.
Turn the 2 knobs to engage the lock.
64766B
2.INSTALL QUARTER TRIM JACK COVER (w/ Spare Tire)
Attach the 7 claws and 3 guides to install the quarter trim jack cover.
62627B
3.INSTALL QUARTER TRIM COVER
Use the same procedure for the other quarter trim cover.
Attach the 2 claws to install the quarter trim cover.
73372
4.INSTALL REAR SEAT SHOULDER BELT HANGER LH
Use the same procedure for the other rear seat shoulder belt hanger.
Attach the claw and guide to install the rear seat shoulder belt hanger.
73371
5.INSTALL REAR SEAT SHOULDER BELT HANGER RH
Use the same procedure described for the LH side.
64746F
6.INSTALL DECK SIDE TRIM CUP HOLDER LH
Attach the 4 claws to install the deck side trim cup holder.
64745H
7.INSTALL DECK SIDE TRIM CUP HOLDER RH
Use the same procedure described for the LH side.
66425A
8.INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Attach the 4 claws to install the rear side rail spacer.
Install the clip.
66415A
9.INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Use the same procedure described for the LH side.
73024
10.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 4 claws to install the front shoulder belt anchor plate.
73023
11.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
63310
12.INSTALL ROOF HEADLINING ASSEMBLY
Place the roof headlining into the vehicle through the back door.
Be careful not to damage the roof headlining when placing it in the cabin.
w/o Sliding Roof:
Attach the 2 clips to install the roof headlining.
w/ Sliding Roof:
Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining.
| *1 | Guide |
| *2 | Fastener |
Connect the connector and attach the 4 clamps to the front pillar RH.
Connect the connector and attach the 3 clamps to the rear pillar LH.
Connect the 2 connectors and attach the 3 clamps to the front pillar RH.
Install the bolt.
Connect the 2 connectors and attach the 3 clamps to the front pillar LH.
w/ Digital Audio Broadcasting Antenna:
Connect the connector and attach the wire harness clamp.
w/ Sliding Roof
Connect the drive gear connector.
w/ Rain Sensor:
Connect the rain sensor connector.
w/ EC Mirror:
Connect the inner mirror connector.
62432B
13.INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH
Install 5 new clips to the No. 1 roof side rail garnish LH.
| *1 | New Clip |
Attach the 5 clips to install the No. 1 roof side rail garnish LH.
62431B
14.INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH
Use the same procedure described for the LH side.
81240D
15.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
Install the No. 2 room light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Rear)>INSTALLATION).
81240
16.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
Install the No. 1 room light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Center)>INSTALLATION).
87834
17.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
89943
18.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
81260A
19.INSTALL MAP LIGHT ASSEMBLY
74348
20.INSTALL VISOR HOLDER
74320
21.INSTALL VISOR ASSEMBLY LH
74310
22.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74318
23.INSTALL VISOR BRACKET COVER LH
74317
24.INSTALL VISOR BRACKET COVER RH
Use the same procedure described for the LH side.
74610U
25.INSTALL REAR ASSIST GRIP ASSEMBLY LH
74610V
26.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
74610A
27.INSTALL ASSIST GRIP SUB-ASSEMBLY
62640P
28.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH
Attach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear quarter trim panel.
Attach the 7 clips to install the rear quarter trim panel.
62630P
29.INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
62520P
30.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
Pass the front seat outer belt floor anchor through the front quarter trim panel.
Attach the 2 clips and 2 guides to install the front quarter trim panel.
Install the bolt.
62510P
31.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
Use the same procedure described for the LH side.
64740C
32.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Attach the 9 claws and 11 clips to install the deck trim side panel.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
Install the front seat outer belt floor anchor with the bolt.
64730B
33.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Connect the connector.
Attach the 9 claws and 11 clips to install the deck trim side panel.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
Install the front seat outer belt floor anchor with the bolt.
73233
34.INSTALL OUTER LAP BELT ANCHOR COVER
Use the same procedure for the other outer lap belt anchor cover.
Attach the 3 claws to install the outer lap belt anchor cover.
62596D
35.INSTALL QUARTER TRIM POCKET TRAY
Attach the 6 claws and 2 guides to install the quarter trim pocket tray.
64712F
36.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
Use the same procedure for the other front deck side trim cover.
Attach the 2 claws to install the front deck side trim cover.
64937A
37.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
Use the same procedure for the other tonneau cover holder cap.
Attach the 2 claws to install the No. 1 tonneau cover holder cap.
64725D
38.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Use the same procedure for the other No. 1 luggage compartment trim hook.
Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.
58570C
39.INSTALL REAR FLOOR CARPET ASSEMBLY
Install the rear floor carpet.
62538E
40.INSTALL QUARTER TRIM COVER HOLE LH
Attach the 2 claws and 2 guides to install the quarter trim cover hole.
62538C
41.INSTALL QUARTER TRIM COVER HOLE RH
Use the same procedure described for the LH side.
58574A
42.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
Attach the 6 claws to install the rear floor mat rear support plate.
Install the 5 screws.
58649C
43.INSTALL MAT SET PLATE COVER
Use the same procedure for all mat set plate covers.
Attach the 2 claws to install the mat set plate cover.
64910M
44.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Install the tonneau cover.
62212
45.INSTALL FRONT PILLAR GARNISH LH
62211
46.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74611F
47.INSTALL NO. 1 ASSIST GRIP
74616C
48.INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH
74615E
49.INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH
Use the same procedure described for the LH side.
62312B
50.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
51.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
52.INSTALL COWL SIDE TRIM BOARD LH
62111C
53.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67920
54.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
67910
55.INSTALL DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure described for the LH side.
56.INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
for LH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type LH Side)>INSTALLATION).
for RH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type RH Side)>INSTALLATION).
57.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).