Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL SYSTEM › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053667 1GR-FE FUEL _0260542 FUEL SYSTEM G

1GR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND FOR FUEL LEAK

a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.


e.

Check the fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.




Hide 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




d.
A224399

Disconnect the No. 1 fuel pipe sub-assembly (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


e.
A290843E01
0.374,2.139 0.558,2.294 0.183,0.155 10 *1 0.189,0.487 0.372,0.642 0.183,0.155 10 *2 1.695,1.106 1.879,1.261 0.183,0.155 10 *3 3.149,1.231 3.333,1.386 0.183,0.155 10 *4 1.897,2.644 2.081,2.798 0.183,0.155 10 *6 1.073,4.083 1.257,4.238 0.183,0.155 10 *7 1.68,1.191 1.605,1.191 1.605,1.191 1.482,0.964 false 0.58,2.225 0.673,2.225 0.673,2.225 0.777,2.538 false 1.282,4.167 1.355,4.167 1.355,4.167 1.679,4.375 false 1.87,2.724 1.769,2.724 1.769,2.724 1.601,2.426 false 1.671,0.282 1.855,0.436 0.183,0.155 10 *5 1.017,0.57 0.416,0.57 false 0.637,1.061 0.637,0.57 false 2.064,4.011 2.248,4.166 0.183,0.155 10 *2 2.034,4.098 1.969,4.098 1.969,4.098 1.826,3.913 false 3.278,1.225 3.278,1.049 3.278,1.049 3.173,0.901 false 1.274,0.373 1.656,0.373 false

Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)

Text in Illustration
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (T Joint)
*4 SST (Pressure Gauge)
*5 SST (Hose Joint)
*6 No. 1 Fuel Tube Sub-assembly
*7 SST (Fuel Tube Connector)


f.

Wipe off any gasoline.


g.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



h.

Operate the fuel pump.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control / ON.



i.

Measure the fuel pressure.

Standard fuel pressure:

321 to 327 kPa (3.27 to 3.33 kgf/cm2, 46.5 to 47.4 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator.

If the pressure is below the specification, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.


j.

Start the engine.


k.

Measure the fuel pressure.

Standard fuel pressure:

321 to 327 kPa (3.27 to 3.33 kgf/cm2, 46.5 to 47.4 psi)


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


n.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.


o.

Connect the No. 1 fuel pipe sub-assembly (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).