Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL PUMP (for Single Tank Type) › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053667 1GR-FE FUEL _0260552 FUEL PUMP(for Single Tank Type) A

1GR-FE FUEL  FUEL PUMP(for Single Tank Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

for Automatic Transmission:

Perform "Inspection After Repairs" after replacing the fuel pump (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of gasoline or grease to a new gasket and install the gasket to the fuel tank.


b.
A220825E09
1.479,2.385 1.406,2.385 1.406,2.385 1.177,2.792 true 1.177,3.01 1.365,3.083 1.365,3.083 1.583,3.083 true 1.625,2.99 1.875,3.24 0.25,0.25 10 true *2 1.5,2.292 1.719,2.49 0.219,0.198 10 false *1

Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.

Text in Illustration
*1 Protrusion
*2 Groove

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



c.

Install the fuel suction with pump and gauge tube to the fuel tank.


d.

Put a new retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.

Text in Illustration
*1 Start Mark (Fuel Tank Side)
*2 Start Mark (Retainer Side)

HINT:
A220826E07
2.281,0.927 2.688,0.5 2.688,0.5 2.781,0.5 true 2.417,0.938 2.771,0.938 true 2.792,0.833 3.063,1.094 0.271,0.26 10 true *1 2.792,0.406 3.042,0.667 0.25,0.26 10 true *2

Make sure the start marks on the retainer and fuel tank are aligned and then tighten the retainer.



e.
A243483E01
0.299,0.182 0.610,0.366 0.311,0.184 10 SST 0.671,0.262 0.897,0.262 0.897,0.262 1.054,0.466 false

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.

·

Engage the claws of SST securely with the fuel pump gauge retainer holes to secure SST.

·

Install SST while pressing the claws of SST against the fuel pump gauge retainer (toward the center of SST).




f.
A243481E07
0.521,0.75 0.615,0.75 0.615,0.75 0.948,1.135 true 1.333,3.104 0.833,3.104 false 1.677,3.083 2.771,3.083 true 2.385,0.156 2.188,0.156 2.188,0.156 2.031,0.26 false 2.146,3.813 1.948,3.813 1.948,3.813 1.667,3.292 false 0.323,0.646 0.552,0.833 0.229,0.188 10 false *1 2.438,0.073 2.823,0.323 0.385,0.25 10 true SST 0.625,3 0.875,3.198 0.25,0.198 10 false *1 2.802,2.99 3.031,3.219 0.229,0.229 10 false *2 1.125,3.677 1.302,3.927 0.177,0.25 10 false A 2.188,3.708 2.448,3.927 0.26,0.219 10 false *1

Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.

SST
09808-14030  

Text in Illustration
*1 Fuel Tank Side Mark
*2 Retainer Side Mark

HINT:

Fit the tips of SST onto the ribs of the retainer.



Hide 77100U 2.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Install the fuel tank sub-assembly (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL TANK>INSTALLATION).