Home › Engine / Hybrid System › 1KD-FTV (FUEL) › FUEL TANK (for 5 Door) › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0260570 FUEL TANK(for 5 Door) A

1KD-FTV FUEL  FUEL TANK(for 5 Door)  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 2.REMOVE REAR SEAT ASSEMBLY LH

a.

for 60/40 Split Double-folding Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>REMOVAL).


b.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>REMOVAL).


Hide 58371F 3.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 67934 4.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

Hide 67918D 5.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58325E 6.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A220797

Remove the 3 screws and rear floor service hole cover.


b.
A220803E01
0.071,0.057 0.335,0.226 0.265,0.169 12 *A 0.071,2.347 0.327,2.514 0.257,0.167 12 *B

Disconnect the fuel pump and sender gauge connector.

Text in Illustration
*A for Single Tank Type
*B for Double Tank Type


Hide 77606 7.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A220805

Remove the 6 bolts and No. 1 fuel tank protector.


b.
A224491

for Half Cover Type:

Remove the 4 bolts and No. 1 fuel tank protector.


Hide 77209D 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223261

Hide 77207A 9.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223105

Hide 77209D 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

A223101

Hide 11.DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)

A223106

Hide 77012 12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223262

Disconnect the fuel tank breather tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77208A 13.DISCONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223102

Disconnect the No. 4 fuel main tube and fuel suction tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 14.DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)

a.
A223280

Disconnect the fuel cut off tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 15.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223281

Disconnect the fuel return tube and No. 2 fuel main tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77012 16.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223282

Disconnect the fuel tank breather tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77213B 17.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A220811

Disconnect the fuel tank to filler pipe hose from the filler pipe.


Hide 77100U 18.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place a transmission jack under the fuel tank.


b.
A220832

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


c.

Slowly lower the transmission jack slightly.


Hide 77651A 19.REMOVE FUEL TANK CUSHION

a.
A220812E01
0.679,0.225 0.863,0.368 0.184,0.143 10 *1 0.886,0.313 0.976,0.313 0.976,0.313 1.176,0.849 false 2.253,0.177 2.437,0.320 0.184,0.143 10 *2 2.46,0.265 2.55,0.265 2.55,0.265 2.75,0.801 false 2.05,1.934 2.234,2.076 0.184,0.143 10 *3 2.257,2.018 2.347,2.018 2.347,2.018 2.547,1.677 false

Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.

Text in Illustration
*1 No. 1 Fuel Tank Cushion
*2 No. 2 Fuel Tank Cushion
*3 No. 3 Fuel Tank Cushion


Hide 77207A 20.REMOVE FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223107E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 2 fuel tube joint clips and pull out the fuel return tube and fuel tank main tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223110

Remove the fuel return tube and fuel tank main tube from the fuel tank.


Hide 77208A 21.REMOVE NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223109E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 2 fuel tube joint clips and pull out the No. 4 fuel main tube and fuel suction tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223112

Detach the clamp and remove the No. 4 fuel main tube from the fuel tank.


c.

Detach the clamp and remove the fuel suction tube from the fuel tank.


Hide 77209D 22.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223241E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 3 fuel tube joint clips and pull out the fuel tank main tube, fuel return tube and No. 2 fuel main tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223243

Detach the clamp and remove the No. 2 fuel main tube from the fuel tank.


c.

Detach the clamp and remove the fuel return tube from the fuel tank.


d.

Remove the fuel tank main tube from the fuel tank.


Hide 77010 23.REMOVE FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)

a.
A243483E01
0.299,0.182 0.610,0.366 0.311,0.184 10 SST 0.671,0.262 0.897,0.262 0.897,0.262 1.054,0.466 false

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Engage the claws of SST securely with the retainer holes to secure SST.

·

Install SST while pressing the claws of SST against the retainer (towards the center of SST).




b.
A243482E01
1.06,0.228 1.376,0.414 0.316,0.187 10 SST 1.438,0.308 1.616,0.308 1.616,0.308 1.788,0.666 false

Using SST, loosen the retainer.

SST
09808-14030  

Text in Illustration
V100135

Turn

HINT:

Fit the tips of SST onto the ribs of the retainer.


NOTICE:
·

When the retainer is loosened, be careful as the fuel tank vent tube will spring upward from the force of the spring.

·

Remove any foreign matter around the fuel tank vent tube before this operation.




c.

Remove the retainer.


d.

Remove the fuel tank vent tube assembly from the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



e.

Remove the gasket from the fuel tank.


Hide 77020A 24.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)

Hide 77643A 25.REMOVE NO. 3 FUEL TANK PROTECTOR

a.
A220823

Remove the 2 bolts.


b.

Detach the 4 clamps and remove the No. 3 fuel tank protector.


Hide 77213B 26.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A220822

Remove the fuel tank to filler pipe hose from the fuel tank.