Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL PUMP (for Double Tank Type) › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260579 FUEL PUMP(for Double Tank Type) A

1GD-FTV FUEL  FUEL PUMP(for Double Tank Type)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of diesel fuel or grease to a new gasket and install the gasket to the fuel tank sub-assembly.


b.
A220825E10
1.479,2.385 1.406,2.385 1.406,2.385 1.177,2.792 true 1.177,3.01 1.365,3.083 1.365,3.083 1.583,3.083 true 1.625,2.99 1.875,3.24 0.25,0.25 10 true *b 1.5,2.292 1.719,2.49 0.219,0.198 10 false *a

Align the protrusion of the fuel suction with pump and gauge tube assembly with the groove of the fuel tank sub-assembly.

Text in Illustration
*a Protrusion
*b Groove

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.

Install the fuel suction with pump and gauge tube assembly to the fuel tank sub-assembly.


d.

Put a new retainer on the fuel tank sub-assembly. While holding the fuel suction with pump and gauge tube assembly, tighten the retainer one complete turn by hand.

Text in Illustration
*a Start Mark (Fuel Tank Side)
*b Start Mark (Retainer Side)

HINT:
A220826E08
2.281,0.927 2.688,0.5 2.688,0.5 2.781,0.5 true 2.417,0.938 2.771,0.938 true 2.792,0.833 3.063,1.094 0.271,0.26 10 true *a 2.792,0.406 3.042,0.667 0.25,0.26 10 true *b

Make sure the start marks on the retainer and fuel tank sub-assembly are aligned and then tighten the retainer.



e.
A243483E01
0.299,0.182 0.610,0.366 0.311,0.184 10 SST 0.671,0.262 0.897,0.262 0.897,0.262 1.054,0.466 false

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Hold the fuel suction with pump and gauge tube assembly upright by hand to ensure that the gasket is not moved out of position.

·

Engage the claws of SST securely with the retainer holes to secure SST.

·

Install SST while pressing the claws of SST against the retainer (toward the center of SST).




f.
A243481E08
0.521,0.75 0.615,0.75 0.615,0.75 0.948,1.135 true 1.333,3.104 0.833,3.104 false 1.677,3.083 2.771,3.083 true 2.385,0.156 2.188,0.156 2.188,0.156 2.031,0.26 false 2.135,3.813 1.938,3.813 1.938,3.813 1.656,3.292 false 0.323,0.635 0.552,0.833 0.229,0.198 10 false *a 2.448,0.073 2.813,0.313 0.365,0.24 10 true SST 0.625,3 0.854,3.177 0.229,0.177 10 false *a 2.802,3 3.042,3.208 0.24,0.208 10 false *b 1.146,3.677 1.302,3.865 0.156,0.188 10 false A 2.167,3.719 2.385,3.917 0.219,0.198 10 false *a

Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank sub-assembly as shown in the illustration.

SST
09808-14030  

Text in Illustration
*a Fuel Tank Side Mark
*b Retainer Side Mark

HINT:

Fit the tips of SST onto the ribs of the retainer.



Hide 77100U 2.INSTALL FUEL TANK SUB-ASSEMBLY