Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL TANK (for 5 Door) › 2015.06–2016.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260580 FUEL TANK(for 5 Door) A

1GD-FTV FUEL  FUEL TANK(for 5 Door)  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A220824E04
0.432,2.664 0.621,2.811 0.189,0.147 10 *a 0.645,2.752 0.744,2.752 0.744,2.752 1.376,3.438 false 2.247,2.798 2.436,2.945 0.189,0.147 10 *b 2.209,2.887 2.11,2.887 2.11,2.887 1.527,3.573 false

Align the fuel tank side mark with the hose side mark.

Text in Illustration
*a Fuel Tank Side Mark
*b Hose Side Mark


b.

Install the fuel tank to filler pipe hose to the fuel tank sub-assembly, and tighten the clamp to secure the hose.


Hide 77643A 2.INSTALL NO. 3 FUEL TANK PROTECTOR

a.

Install the No. 3 fuel tank protector and attach the 4 clamps.


b.

Install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 77010 3.INSTALL FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)

a.

Apply a light coat of diesel fuel or grease to a new gasket and install the gasket to the fuel tank sub-assembly.


b.
A220825E10
1.479,2.385 1.406,2.385 1.406,2.385 1.177,2.792 true 1.177,3.01 1.365,3.083 1.365,3.083 1.583,3.083 true 1.625,2.99 1.875,3.24 0.25,0.25 10 true *b 1.5,2.292 1.719,2.49 0.219,0.198 10 false *a

Align the protrusion of the fuel tank vent tube assembly with the groove of the fuel tank sub-assembly.

Text in Illustration
*a Protrusion
*b Groove

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.

Install the fuel tank vent tube assembly to the fuel tank sub-assembly.


d.

Put a new retainer on the fuel tank sub-assembly. While holding the fuel tank vent tube assembly, tighten the retainer one complete turn by hand.

Text in Illustration
*a Start Mark (Fuel Tank Side)
*b Start Mark (Retainer Side)

HINT:
A220826E08
2.281,0.927 2.688,0.5 2.688,0.5 2.781,0.5 true 2.417,0.938 2.771,0.938 true 2.792,0.833 3.063,1.094 0.271,0.26 10 true *a 2.792,0.406 3.042,0.667 0.25,0.26 10 true *b

Make sure the start marks on the retainer and fuel tank sub-assembly are aligned and then tighten the retainer.



e.
A243483E01
0.299,0.182 0.610,0.366 0.311,0.184 10 SST 0.671,0.262 0.897,0.262 0.897,0.262 1.054,0.466 false

Set SST on the retainer.

SST
09808-14030  

HINT:
·

Hold the fuel tank vent tube assembly upright by hand to ensure that the gasket is not moved out of position.

·

Engage the claws of SST securely with the retainer holes to secure SST.

·

Install SST while pressing the claws of SST against the retainer (toward the center of SST).




f.
A243481E08
0.521,0.75 0.615,0.75 0.615,0.75 0.948,1.135 true 1.333,3.104 0.833,3.104 false 1.677,3.083 2.771,3.083 true 2.385,0.156 2.188,0.156 2.188,0.156 2.031,0.26 false 2.135,3.813 1.938,3.813 1.938,3.813 1.656,3.292 false 0.323,0.635 0.552,0.833 0.229,0.198 10 false *a 2.448,0.073 2.813,0.313 0.365,0.24 10 true SST 0.625,3 0.854,3.177 0.229,0.177 10 false *a 2.802,3 3.042,3.208 0.24,0.208 10 false *b 1.146,3.677 1.302,3.865 0.156,0.188 10 false A 2.167,3.719 2.385,3.917 0.219,0.198 10 false *a

Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.

SST
09808-14030  

Text in Illustration
*a Fuel Tank Side Mark
*b Retainer Side Mark

HINT:

Fit the tips of SST onto the ribs of the retainer.



Hide 77020A 4.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)

Hide 77207A 5.INSTALL FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223113

Install the fuel return tube sub-assembly and fuel tank main tube sub-assembly with the 2 fuel tube joint clips.

NOTICE:
·
A118171E07
2.57,0.9 2.764,1.046 0.194,0.146 10 *4 2.543,0.989 1.629,0.989 false 0.231,0.553 0.425,0.699 0.194,0.146 10 *1 0.973,0.633 0.448,0.633 false 0.037,1.255 0.230,1.401 0.194,0.146 10 *2 0.973,1.335 0.253,1.335 false 0.973,1.179 0.359,1.179 0.359,1.179 0.359,1.334 false 1.971,0.033 2.165,0.179 0.194,0.146 10 *3 1.949,0.123 1.866,0.123 1.866,0.123 1.703,0.496 false 0.884,4.269 1.078,4.415 0.194,0.146 10 *a 2.56,4.269 2.754,4.415 0.194,0.146 10 *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel return tube sub-assembly and fuel tank main tube sub-assembly to the fuel tank sub-assembly.


Hide 77209D 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223115

Install the fuel tank main tube sub-assembly, fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly with the 3 fuel tube joint clips.

NOTICE:
·
A118171E07
2.57,0.9 2.764,1.046 0.194,0.146 10 *4 2.543,0.989 1.629,0.989 false 0.231,0.553 0.425,0.699 0.194,0.146 10 *1 0.973,0.633 0.448,0.633 false 0.037,1.255 0.230,1.401 0.194,0.146 10 *2 0.973,1.335 0.253,1.335 false 0.973,1.179 0.359,1.179 0.359,1.179 0.359,1.334 false 1.971,0.033 2.165,0.179 0.194,0.146 10 *3 1.949,0.123 1.866,0.123 1.866,0.123 1.703,0.496 false 0.884,4.269 1.078,4.415 0.194,0.146 10 *a 2.56,4.269 2.754,4.415 0.194,0.146 10 *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel tank main tube sub-assembly to the fuel tank sub-assembly.


c.

Install the fuel return tube sub-assembly to the fuel tank sub-assembly and attach the clamp.


d.

Install the No. 2 fuel main tube sub-assembly to the fuel tank sub-assembly and attach the clamp.


Hide 77208A 7.INSTALL NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223242

Install the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly with the 2 fuel tube joint clips.

NOTICE:
·
A118171E07
2.57,0.9 2.764,1.046 0.194,0.146 10 *4 2.543,0.989 1.629,0.989 false 0.231,0.553 0.425,0.699 0.194,0.146 10 *1 0.973,0.633 0.448,0.633 false 0.037,1.255 0.230,1.401 0.194,0.146 10 *2 0.973,1.335 0.253,1.335 false 0.973,1.179 0.359,1.179 0.359,1.179 0.359,1.334 false 1.971,0.033 2.165,0.179 0.194,0.146 10 *3 1.949,0.123 1.866,0.123 1.866,0.123 1.703,0.496 false 0.884,4.269 1.078,4.415 0.194,0.146 10 *a 2.56,4.269 2.754,4.415 0.194,0.146 10 *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel suction tube sub-assembly to the fuel tank sub-assembly and attach the clamp.


c.

Install the No. 4 fuel main tube sub-assembly to the fuel tank sub-assembly and attach the clamp.


Hide 77651A 8.INSTALL FUEL TANK CUSHION

a.

Install 3 new fuel tank cushions to the fuel tank sub-assembly.


Hide 77100U 9.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank sub-assembly on a transmission jack and lift up the transmission jack.

NOTICE:

Do not allow the fuel tank sub-assembly to contact the vehicle, especially the differential.



b.

Install the 2 fuel tank bands with the 2 pins and 2 clips.


c.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 77213B 10.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the filler pipe, and tighten the clamp to secure the hose.


Hide 77012 11.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

a.

Connect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 12.CONNECT FUEL CUT OFF TUBE (for Single Tank Type)

a.

Connect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77012 13.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 14.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 15.CONNECT FUEL CUT OFF TUBE (for Double Tank Type)

a.

Connect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77208A 16.CONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 17.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.

Connect the fuel return tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77209D 18.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.

Connect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77209D 19.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77606 20.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

for Type A:

i.

Install the No. 1 fuel tank protector sub-assembly with the 6 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.

for Type B:

i.

Install the No. 1 fuel tank protector sub-assembly with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



Hide 58325E 21.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel pump and fuel sender gauge connector.


b.

Install the rear floor service hole cover with the 3 screws.


Hide 67918D 22.INSTALL REAR DOOR SCUFF PLATE LH

Hide 67934 23.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

Hide 58371F 24.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 25.INSTALL REAR SEAT ASSEMBLY LH

Hide 26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).