Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL FILTER (for Cylinder Block Side)
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260588 FUEL FILTER(for Cylinder Block Side) A

1GD-FTV FUEL  FUEL FILTER(for Cylinder Block Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

Clean the fuel filter assembly and remove dirt completely.


PROCEDURE

Hide 25804A 1.REMOVE VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)

Hide 2.REMOVE FUEL FILTER CAP WITH ELEMENT

a.
A339762

Disconnect the crankshaft position sensor connector and remove the bolt.


b.

Detach the 2 clamps and disconnect the engine wire.


c.
A339673

Remove the union bolt and gasket, disconnect the No. 4 fuel pipe sub-assembly from the fuel filter assembly.


d.
A339675

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter assembly.

NOTICE:

Do not scratch or dent the installation surface of the No. 4 fuel pipe sub-assembly.



e.
A339635

Remove the union bolt and gasket, disconnect the No. 3 fuel pipe from the fuel filter assembly.


f.
A339637

Loosen the 4 screws.


g.
A339676

Remove the 2 nuts and disconnect the fuel filter assembly.


h.
A339637

Remove the 4 screws and fuel filter cap with element from the fuel filter assembly.

HINT:

Use a container to catch the draining diesel fuel.



i.
A339638

Remove the O-ring from the fuel filter assembly.


Hide 3.INSTALL FUEL FILTER CAP WITH ELEMENT

a.

Apply a light coat of diesel fuel to a new O-ring.


b.

Install the O-ring to the fuel filter assembly.


c.

Temporarily install a new fuel filter element with cap to the fuel filter assembly with the 4 screws.


d.
A362715E01
0.722,3.118 0.879,3.280 0.158,0.162 10 1 2.589,1.99 2.746,2.152 0.158,0.162 10 2 0.719,1.981 0.877,2.143 0.158,0.162 10 3 2.589,3.139 2.747,3.302 0.158,0.162 10 4

Tighten the 4 screws in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of screw 1 after tightening screw 4.



e.

Connect the fuel filter assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Install the No. 3 fuel pipe and a new gasket to the fuel filter assembly with the union bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
A339639E04
2.396,3.719 2.219,3.719 2.219,3.719 1.719,3.24 true 2.417,3.625 2.688,3.854 0.271,0.229 10 true *a 1.417,2.573 1.667,2.781 0.25,0.208 10 true *b 1.792,2.573 2.042,2.771 0.25,0.198 10 true *b

Install the 2 fuel pipe clamps to the fuel filter assembly and No. 3 fuel pipe.

Text in Illustration
*a Paint Mark
*b 0 to 2 mm (0 to 0.0787 in.)

NOTICE:

Be careful that the fuel pipe clamp and No. 4 fuel pipe sub-assembly do not interfere with each other.


HINT:

Make sure the fuel pipe clamp is oriented as shown in the illustration.



h.

Install the No. 4 fuel pipe sub-assembly and a new gasket to the fuel filter assembly with the union bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


i.

Connect the crankshaft position sensor connector.


j.

Attach the 2 clamps and connect the engine wire with the bolt.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 25804A 4.INSTALL VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)