Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053678 1GR-FE INTAKE / EXHAUST _0260642 INTAKE MANIFOLD A

1GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


PROCEDURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 11259 6.REMOVE V-BANK COVER

a.
A229925E01
3.107,0.606 3.274,0.769 0.167,0.162 10 *1 1.136,0.536 1.304,0.699 0.167,0.162 10 *2 1.107,0.626 1.028,0.626 false 1.028,0.623 0.942,0.817 false 2.751,0.695 3.083,0.695 false

Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

Text in Illustration
*1 Pin
*2 Hook


Hide 17881 7.REMOVE NO. 1 AIR CLEANER HOSE

a.
A221455

Disconnect the ventilation hose and vacuum hose.


b.

Detach the wire harness clamp.


c.

Remove the bolt and loosen the 2 hose clamps.


d.

Remove the No. 1 air cleaner hose.


Hide 17360 8.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

a.
A221459

for Bank 1 Side:

Remove the bolt and disconnect the air tube assembly from the emission control valve set.


b.
A221458

for Bank 2 Side:

Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.


Hide 17129 9.REMOVE INTAKE AIR SURGE TANK

a.
A221456

Disconnect the throttle body connector.


b.

Disconnect the No. 4 water by-pass hose.


c.

Disconnect the No. 5 water by-pass hose.


d.
A221457

Disconnect the No. 1 fuel vapor feed hose.


e.

Disconnect the No. 1 vacuum switching valve connector.


f.

Disconnect the No. 1 ventilation hose.


g.
A221464

Detach the 2 heater hose clamps.


h.
A221460

Remove the 2 bolts and throttle body bracket.


i.
A221461

Using a clip remover, detach the wire harness clamp.


j.
A221462

Remove the 2 bolts and No. 1 surge tank stay.


k.
A221463

Remove the 2 bolts and No. 2 surge tank stay.


l.
A221465

Remove the 2 nuts, 4 bolts and intake air surge tank.


m.

Remove the gasket.


Hide 23807 10.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 17111 11.REMOVE INTAKE MANIFOLD

a.
A221466

Remove the 4 nuts, 6 bolts and 2 gaskets.