Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260654 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A356216C02
3.25,0.344 3.052,0.146 3.052,0.146 2.833,0.146 true 2.667,0.052 2.896,0.24 0.229,0.188 10 true *1
*1 Protrusion
V100135

Rear side


Install a new gasket to the cylinder head sub-assembly.

HINT:

Install the gasket with the protrusion the rear side of the vehicle as shown in the illustration.



b.

Temporarily install the intake manifold with the 7 bolts and 2 nuts.


c.
A352783C02
0.208,0.219 0.385,0.396 0.177,0.177 10 true 1 0.656,0.229 0.833,0.406 0.177,0.177 10 true 6 1.531,0.208 1.708,0.385 0.177,0.177 10 true 9 2.302,0.208 2.479,0.385 0.177,0.177 10 true 4 2.865,0.208 3.042,0.385 0.177,0.177 10 true 2 0.417,1.813 0.594,1.99 0.177,0.177 10 true 8 1.156,1.802 1.333,1.979 0.177,0.177 10 true 3 1.938,1.792 2.115,1.969 0.177,0.177 10 true 7 2.677,1.802 2.854,1.979 0.177,0.177 10 true 5
V100135

Bolt
V100136

Nut


Tighten the 7 bolts and 2 nuts in the order shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


d.

Connect the wire harness bracket A, B and C with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 25804 2.INSTALL VACUUM CONTROL VALVE SET

a.

Install the vacuum control valve set with bolt to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the 2 vacuum hoses to the swirl control valve actuator and vacuum transmitting pipe subassembly.


c.

Connect the wire harness clamp and vacuum control valve set connector.


Hide 23770 3.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Install the No. 2 nozzle leakage pipe assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 6 fuel hose to the No. 3 nozzle leakage pipe assembly and slide the clamp to secure the hoses.


c.

Install the No. 4 fuel hose and No. 5 fuel hose to the No. 2 nozzle leakage pipe assembly, and slide the 4 clamps to secure the hose.


Hide 23804C 4.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:

When replacing the fuel supply pump assembly, it is necessary to replace the fuel inlet pipe subassembly, No. 1 injection pipe clamp and No. 2 injection pipe clamp with a new one. Keep the fuel inlet pipe sub-assembly free of foreign matter.


a.

When replacing the No. 1 injection pipe clamp and No. 2 injection pipe clamp with new ones:

i.
A454527C02
2.073,1.844 2.51,1.844 true 2.177,1.24 2.615,1.24 true 2.552,1.74 2.865,1.896 0.313,0.156 10 false *1 2.667,1.135 2.979,1.292 0.313,0.156 10 false *2
*1 No. 1 Injection Pipe Clamp
*2 No. 2 Injection Pipe Clamp


Set a new No. 1 injection pipe clamp and No. 2 injection pipe clamp on the fuel inlet pipe sub-assembly.

NOTICE:
A454528C01
0.135,0.094 0.448,0.25 0.313,0.156 10 false *a
*a INCORRECT


When installing, do not pinch together the No. 1 injection pipe clamp or No. 2 injection pipe clamp.




b.

Temporarily install the fuel inlet pipe sub-assembly by turning its union nut by hand until it stops.


c.

When reusing the No. 1 injection pipe clamp and No. 2 injection pipe clamp:

i.

Install the No. 1 injection pipe clamp and No. 2 injection pipe clamp with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



d.

When replacing the No. 1 injection pipe clamp and No. 2 injection pipe clamp with new ones:

i.
A454529

Pinch together the clamp while aligning it with the bolt installation hole of the No. 2 injection pipe clamp by hand, and then install the bolt to the intake manifold.

NOTICE:
·

Do not pinch together the No. 2 injection pipe clamp while tightening the bolt.

·

Pinch together the No. 2 injection pipe clamp by hand, and then install the bolt.

·

Do not forcibly align the position of the hole using the bolt.



Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A454530

Pinch together the clamp while aligning it with the bolt installation hole of the No. 1 injection pipe clamp by hand, and then install the bolt to the intake manifold.

NOTICE:
·

Do not pinch together the No. 1 injection pipe clamp while tightening the bolt.

·

Pinch together the No. 1 injection pipe clamp by hand, and then install the bolt.

·

Do not forcibly align the position of the hole using the bolt.



Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



e.

With Common Rail Side Number Mark (24N):

i.
A439101C01
2.438,0.938 2.438,0.76 2.438,0.76 2.667,0.688 true 2.375,0.948 2.688,1.104 0.313,0.156 10 false *a
*a Number Mark (24N)


Make sure that the "24N" mark faces the common rail side of the fuel inlet pipe sub-assembly at the position shown in the illustration.

NOTICE:

Check for the number mark and tighten the parts to the specified tightening torque.



ii.
A412879C02
1.531,1.813 1.542,1.354 true 2.667,0.885 2.979,1.042 0.313,0.156 10 true *a 1.417,1.823 1.792,2 0.375,0.177 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.

SST
09245-11010  

Torque:
Specified tightening torque : 24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 18.8 N*m (192 kgf*cm, 14 ft.*lbf)




iii.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 24 N*m (245 kgf*cm, 18 ft.*lbf)





f.

Without Common Rail Side Number Mark (24N):

i.
A412879C02
1.531,1.813 1.542,1.354 true 2.667,0.885 2.979,1.042 0.313,0.156 10 true *a 1.417,1.823 1.792,2 0.375,0.177 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.

SST
09245-11010  

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 31 N*m (316 kgf*cm, 23 ft.*lbf)




ii.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 41 N*m (418 kgf*cm, 30 ft.*lbf)





Hide 23815D 5.INSTALL NO. 3 FUEL PIPE

a.

Temporarily install the No. 3 fuel pipe and 2 new gaskets with the union bolt and supply pump hollow screw.


b.

Tighten the union bolt and supply pump hollow screw.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
A339639C06
2.563,2.448 2.385,2.448 2.385,2.448 1.885,3.198 false 1.167,2.729 1.906,2.729 1.906,2.729 1.906,2.802 false 1.542,2.802 1.542,2.729 false 2.583,2.354 2.844,2.563 0.26,0.208 10 true *a 0.948,2.667 1.146,2.813 0.198,0.146 10 false *b
*a Torque Wrench Fulcrum Length
*b 0 to 2 mm (0 to 0.787 in.)


Install the 2 fuel pipe clamps to the No. 3 fuel pipe and fuel filter.


d.
A454519

Connect the connector.


e.

Attach the clamp to connect the wire harness.


Hide 23804D 6.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

a.

Temporarily install the No. 4 fuel pipe sub-assembly and 2 new gaskets with the 2 union bolts and bolt.


b.
A356214C08
2.479,3 2.677,3.198 0.198,0.198 10 true 1 3,3.031 3.26,3.198 0.26,0.167 10 true 2 1.313,1.677 1.51,1.875 0.198,0.198 10 true 3
V100136

Union Bolt
V100137

Bolt


Tighten the 2 union bolts and bolts in the order shown in the illustration.

Torque:
union bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 4 fuel pipe sub-assembly to the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 17118 7.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the wiring harness clamp bracket with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 8.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 2 wire harness clamps.


c.

Connect the diesel throttle body assembly connector and pre-stroke control valve connector.


Hide 23812D 9.INSTALL NO. 2 FUEL PIPE

a.

Connect the No. 2 fuel pipe and with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11409 10.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring and grommet.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the vacuum hose to the intake manifold.


e.

Install the engine oil level dipstick.


f.

w/ No. 2 Fuel Pipe Clamp:

Attach the No. 2 fuel pipe clamp to the engine oil level dipstick guide.


Hide 25800 11.INSTALL EGR COOLER ASSEMBLY

Hide 53737A 12.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).