Home › Engine / Hybrid System › 1GD-FTV (COOLING) › THERMOSTAT
RM27T0E _51 Engine / Hybrid System _053685 1GD-FTV COOLING _0260679 THERMOSTAT A

1GD-FTV COOLING  THERMOSTAT  INSTALLATION  


PROCEDURE

Hide 16331A 1.INSTALL THERMOSTAT

a.
A341325E02
1.188,1.625 1.188,1.313 false 2.219,1.615 2.219,1.354 false 2.156,0.563 2.49,0.802 0.333,0.24 10 false *b 1.083,0.563 1.417,0.802 0.333,0.24 10 false *a 1.115,1.625 1.292,1.792 0.177,0.167 10 false *1 2.135,1.635 2.313,1.802 0.177,0.167 10 false *1

Install a new gasket to the thermostat as shown in the illustration.

Text in Illustration
*1 Gasket
*a CORRECT
*b INCORRECT

NOTICE:

When installing the gasket to the thermostat, be careful not to deform the gasket. Make sure that the groove of the gasket is properly installed to the thermostat as shown in the illustration.



b.
A341232E02
1.958,0.333 2.104,0.094 2.104,0.094 2.219,0.094 true 1.479,0.333 1.333,0.094 1.333,0.094 1.219,0.094 true 1.74,0.656 2.438,0.656 false 1.625,0.021 1.823,0.208 0.198,0.188 10 true *a 2.24,0.021 2.448,0.208 0.208,0.188 10 true *b 1.021,0.031 1.219,0.219 0.198,0.188 10 true *b 2.469,0.573 2.708,0.76 0.24,0.188 10 true *c

Insert the thermostat into the engine water pump assembly with the jiggle valve facing straight upward.

Text in Illustration
*a Upward
*b 30°
*c Jiggle Valve

HINT:

The jiggle valve may be set to within 30° on either side of the prescribed position.



Hide 16321 2.INSTALL WATER INLET

a.

Install the water inlet with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16572D 3.CONNECT NO. 2 RADIATOR HOSE

a.
A360288E02
0.635,2.573 0.854,2.792 0.219,0.219 10 false A 1.396,2.354 1.615,2.573 0.219,0.219 10 false A 2.125,2.375 2.344,2.594 0.219,0.219 10 false *a 1.469,2.917 1.656,3.104 0.188,0.188 10 false *b

Connect the No. 2 radiator hose to the water inlet and slide the hose clamp to secure the hose as shown in the illustration.

Text in Illustration
*a Upper Side
*b Right Side of Vehicle


Hide 16207 4.CONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass pipe sub-assembly to the engine water pump assembly and water inlet with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 87209 5.INSTALL WATER HOSE SUB-ASSEMBLY (for Cold Area Specification Vehicles)

a.

Connect the water hose sub-assembly to the viscous heater with magnet clutch and heater pipes, and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Slide the 4 hose clamps to secure the water hose sub-assembly.