When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Upon receiving the signal, the ECM cancels cruise control. Even if there is a malfunction in the stop light signal circuit while cruise control is in operation, normal driving is maintained due to a fail-safe function.
When the brake pedal is depressed, positive voltage is applied to terminal STP of the ECM through the STOP fuse and stop light switch, and the ECM cancels cruise control.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0571 | The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more. | ·
Stop light switch circuit ·
Stop light switch assembly ·
ECM |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the A85 switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-1 (B) - Body ground | Always | 11 to 14 V |
| A85-5 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-3 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
OK
NG
for 1GR-FE, Automatic Transmission
Disconnect the A85 switch connector.
Disconnect the F56 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-4 (L) - F56-34 (ST1-) | Always | Below 1 Ω |
| A85-2 (L) - F56-35 (STP) | ||
| A85-4 (L) - Body ground | Always | 10 kΩ or higher |
| A85-2 (L) - Body ground |
for 1GR-FE, Manual Transmission
Disconnect the A85 switch connector.
Disconnect the G55 and G56 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-4 (L) - G55-8 (ST1-) | Always | Below 1 Ω |
| A85-2 (L) - G56-18 (STP) | ||
| A85-4 (L) - Body ground | Always | 10 kΩ or higher |
| A85-2 (L) - Body ground |
for 2TR-FE
Disconnect the A85 switch connector.
Disconnect the G180 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-4 (L) - G180-11 (ST1-) | Always | Below 1 Ω |
| A85-2 (L) - G180-10 (STP) | ||
| A85-4 (L) - Body ground | Always | 10 kΩ or higher |
| A85-2 (L) - Body ground |
for 1KD-FTV
Disconnect the A85 switch connector.
Disconnect the G57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-4 (L) - G57-9 (ST1-) | Always | Below 1 Ω |
| A85-2 (L) - G57-8 (STP) | ||
| A85-4 (L) - Body ground | Always | 10 kΩ or higher |
| A85-2 (L) - Body ground |
for 1GD-FTV
Disconnect the A85 switch connector.
Disconnect the G185 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-4 (L) - G185-12 (ST1-) | Always | Below 1 Ω |
| A85-2 (L) - G185-13 (STP) | ||
| A85-4 (L) - Body ground | Always | 10 kΩ or higher |
| A85-2 (L) - Body ground |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for 1GR-FE, 2TR-FE | A |
| for 1KD-FTV, 1GD-FTV | B |
A
B
Temporarily replace the stop light switch with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE) | B |
| NG (for 2TR-FE) | C |
A
B
C
Temporarily replace the stop light switch with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1KD-FTV) | B |
| NG (for 1GD-FTV) | C |
A
B
C