Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260748 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Wiper Signal Circuit  


DESCRIPTION

When the driving support ECU detects that the wipers are operating at high speed, the dynamic radar cruise control system is canceled.

WIRING DIAGRAM

E200952E09
4.709,1.797 5.076,1.942 0.368,0.145 10 G119 5.003,0.97 5.371,1.116 0.368,0.145 10 WIP2 2.192,0.97 2.381,1.116 0.189,0.145 10 +2 4.703,0.872 4.889,1.018 0.185,0.145 10 32 2.479,0.704 2.731,1.016 0.251,0.312 10 1*1 9*2 4.709,1.933 6.024,2.079 1.316,0.145 10 Driving Support ECU 3.266,0.778 4.189,0.926 0.923,0.149 10 WIP FR NO. 2 1.514,1.783 1.896,1.928 0.382,0.145 10 G120 1.514,1.94 3.063,2.256 1.548,0.316 10 Windshield Wiper Switch Assembly 0.082,2.364 1.373,2.506 1.291,0.142 10 *2: for RH Side 0.082,2.066 1.373,2.208 1.291,0.142 10 *1: for LH Side

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WINDSHIELD WIPER SWITCH ASSEMBLY
a.
U170733E01
0.097,0.045 0.251,0.199 0.154,0.154 10 *a 1.52,0.206 1.885,0.350 0.364,0.144 10 G120 0.196,0.859 0.534,1.003 0.338,0.144 10 +2*B 1.087,0.933 0.614,0.933 false 2.761,1.607 3.099,1.751 0.338,0.144 10 +2*A 2.398,1.019 2.63,1.694 2.63,1.694 2.733,1.694 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (+2) - Body ground*1
9 (+2) - Body ground*2
Ignition switch ON, windshield wiper switch Hi 11 to 14 V
Ignition switch ON, windshield wiper switch Lo Approximately 9 V
Ignition switch ON, windshield wiper switch off Below 1 V


*1: for LH Side

*2: for RH Side


Text in illustration
*A for RH Side
*B for LH Side
*a Component with harness connected
(Windshield Wiper Switch Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER SWITCH - DRIVING SUPPORT ECU)

NG

REPLACE WINDSHIELD WASHER SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WASHER SWITCH - DRIVING SUPPORT ECU)
a.

Disconnect the G119 ECU connector.


b.

Disconnect the G120 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-32 (WIP2) - G120-1 (+2)*1 Always Below 1 Ω
G119-32 (WIP2) - G120-9 (+2)*2
G119-32 (WIP2) - Body ground Always 10 kΩ or higher


*1: for LH Side

*2: for RH Side




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR