Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

C221301E01
4.885,2.063 5.208,1.125 5.208,1.125 5.271,1.125 true 5.031,2.208 5.188,2.573 5.188,2.573 5.26,2.573 true 5.875,2.271 6,2.573 6,2.573 6.063,2.573 true 6.115,2.479 7,2.698 0.885,0.219 10 false Solenoid Coil 0.104,0.677 1.354,0.896 1.25,0.219 10 false Hydraulic Pressure 2.563,3.01 3.125,3.229 0.563,0.219 10 false Current 5.313,2.49 5.844,2.708 0.531,0.219 10 false Sleeve 5.323,1.031 6.167,1.25 0.844,0.219 10 false Spool Valve

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P2714 The TCM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic*1, 1-trip detection logic*2).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed

·

1-2 shift valve is stuck

·

Valve body is blocked

·

Torque converter clutch assembly

·

Automatic transmission (clutch, brake, gear, etc.)



*1: w/ OBD

*2: w/o OBD

MONITOR DESCRIPTION

The TCM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The TCM turns on the MIL and outputs this DTC when the amount of heat absorption exceeds the specified value.

There are two reasons that the speed may be different.

·

When shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.

·

When the shift solenoid valve remains on or off, the gear position commanded by the TCM and the actual gear position are not the same.


NOTICE:

If the vehicle continues to be driven under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2714)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P2714 is output A
P2714 and other DTCs are output B

HINT:

If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

NG

7.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)
CAUTION:

This test should always be performed with at least 2 people.


NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.



c.

Warm up the engine.


d.

Enter the following menus: Powertrain / ECT / Active Test.


e.

According to the display on the tester, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.


ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th up-shift must be performed with the accelerator pedal released.

·

The 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the TCM is shown in the Data List display on the tester.




f.

Compare the TCM gear shift command and actual gear position.

OK:

Gear position changes in accordance with the tester command.


Result
System Condition TCM Gear Shift Command Proceed to
1st 2nd 3rd 4th 5th
Malfunction Shift solenoid S1 Stuck ON 1st 2nd 2nd 1st N*1 A
Stuck OFF 4th 3rd 3rd 4th 5th
Shift solenoid S2 Stuck ON*2 2nd 2nd 3rd 3rd N*1 B
Stuck OFF*3 1st 1st 4th 4th 5th
Shift solenoid SL2 Stuck ON 1st 2nd 3rd 4th N*1 C
Stuck OFF 1st 2nd 3rd 4th 5th
Shift solenoid SR Stuck ON*4 1st 2nd 3rd 4th 5th D
Stuck OFF*5 1st 2nd 3rd 4th 4th
Normal 1st 2nd 3rd 4th 5th E

HINT:
·

*1: Neutral

·

*2: When shift solenoid valve S2 is stuck ON, the vehicle cannot drive in reverse.

·

*3: When shift solenoid valve S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.

·

*4: Stuck ON condition can be determined by checking if shift shock has increased excessively.

·

*5: When shift solenoid valve SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.

·

Gear shifts can be determined by paying attention to changes in rpm.





A

4.INSPECT SHIFT SOLENOID VALVE S1

B

10.INSPECT SHIFT SOLENOID VALVE S2

C

13.INSPECT SHIFT SOLENOID VALVE SL2

D

16.INSPECT SHIFT SOLENOID VALVE SR

E

20.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE S1

OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

7.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E05
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)


OK

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

9.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

9.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

10.INSPECT SHIFT SOLENOID VALVE S2

OK

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

12.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

12.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

13.INSPECT SHIFT SOLENOID VALVE SL2

OK

14.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

14.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

15.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

15.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

17.INSPECT SHIFT SOLENOID VALVE SL1

OK

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

19.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

19.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

20.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E05
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)


OK

21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

21.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

22.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

22.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG