Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260761 AUTOMATIC TRANSMISSION ASSEMBLY A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 28800N 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See Page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 51405A 2.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 3.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 53736B 5.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

Hide 36179 7.REMOVE LOWER TRANSFER CASE PROTECTOR

a.

Remove the 4 bolts and lower transfer case protector.


Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37140 9.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 10.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 33820B 11.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C214587

Remove the nut and clip and disconnect the transmission control cable from the transmission.


Hide 32921 12.DISCONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE

a.

Remove the 3 bolts and open the 3 oil cooler tube clamps.

U170257


b.

Using a union nut wrench, disconnect the No. 1 inlet oil cooler tube and No. 1 outlet oil cooler tube from each oil cooler tube union.


Hide 28100 13.REMOVE STARTER ASSEMBLY

a.

for 2.2 kW Type:

Remove the starter (See page Engine / Hybrid System>1KD-FTV (STARTING)>STARTER (for 2.2 kW Type)>REMOVAL).


b.

for 2.7 kW Type:

Remove the starter (See page Engine / Hybrid System>1KD-FTV (STARTING)>STARTER (for 2.7 kW Type)>REMOVAL).


c.

for 3.0 kW Type:

Remove the starter (See page Engine / Hybrid System>1KD-FTV (STARTING)>STARTER (for 3.0 kW Type)>REMOVAL).


Hide 12156 14.REMOVE OIL PAN INSULATOR

C214467

a.

Remove the 2 bolts and oil pan insulator.


Hide 35030 15.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C159641

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


Hide 51226A 16.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.
C214435

Remove the 8 bolts, front bracket suspension member LH and front bracket suspension member RH.


Hide 51204 17.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C171489

Remove the 4 bolts of the rear engine mounting insulator.


b.
C214464

Remove the 4 nuts, 4 bolts and frame crossmember.


Hide 12371 18.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C171491

a.

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 32101A 19.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

C218118

a.

Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

If it is difficult to reach the setting bolts with the wrench, raise or lower the transmission jack until there is sufficient space for the wrench.



Hide 82121 20.DISCONNECT WIRE HARNESS AND CONNECTOR

a.
C157274

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



b.

Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

U170030

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



c.

Detach the 7 harness clamps and disconnect the wire harness.


Hide 35030 21.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C232274

a.

Remove the 9 bolts and automatic transmission.

NOTICE:

Do not use excess force to pry on the transmission assembly.



Hide 82715 22.REMOVE WIRING HARNESS CLAMP BRACKET

a.
C231679

Remove the bolt and wiring harness clamp bracket.


Hide 36100 23.REMOVE TRANSFER ASSEMBLY

Hide 33823 24.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232

a.

Remove the 2 bolts and transmission control cable bracket.


Hide 32000 25.REMOVE TORQUE CONVERTER ASSEMBLY