Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

Refer to DTC P0711 (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>P0711).

DTC Code DTC Detection Condition Trouble Area
P0712 ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
·

Short in No. 1 ATF temperature sensor circuit

·

No. 1 ATF temperature sensor (transmission wire)

·

TCM


P0713 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either condition is met (1-trip detection logic):
(A) 550 sec. or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 sec. or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).
·

Open in No. 1 ATF temperature sensor circuit

·

No. 1 ATF temperature sensor (transmission wire)

·

TCM



MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is below 79 Ω*1 or higher than 156 kΩ*2, the TCM interprets this as a fault in the ATF temperature sensor or wiring. The TCM will illuminate the MIL and store the DTC.

HINT:
·

*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.

·

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

·

The ATF temperature can be checked on the intelligent tester display.



WIRING DIAGRAM

C155188E21
5.509,1.162 5.980,1.364 0.471,0.202 10 THO1 5.199,1.286 5.497,1.487 0.297,0.202 10 25 5.193,2.441 5.491,2.643 0.297,0.202 10 24 3.51,1.286 3.808,1.487 0.297,0.202 10 10 3.51,2.441 3.808,2.643 0.297,0.202 10 9 1.066,1.286 1.233,1.487 0.168,0.202 10 2 5.193,3.797 5.491,3.999 0.297,0.202 10 23 5.509,2.317 5.980,2.519 0.471,0.202 10 THO2 3.05,2.177 3.482,2.379 0.432,0.202 10 OT2+ 1.299,1.022 1.770,1.224 0.471,0.202 10 OT- 1.296,2.177 1.767,2.379 0.471,0.202 10 OT2- 5.509,3.672 5.980,3.874 0.471,0.202 10 E2 5.77,4.226 6.241,4.428 0.471,0.202 10 G69 5.77,4.412 6.241,4.614 0.471,0.202 10 TCM 1.763,3.141 2.234,3.343 0.471,0.202 10 C30 1.763,3.327 3.061,3.529 1.297,0.202 10 Transmission Wire 1.394,1.515 3.412,1.717 2.017,0.202 10 No. 1 ATF Temperature Sensor 1.394,2.668 3.412,2.870 2.017,0.202 10 No. 2 ATF Temperature Sensor 1.066,2.441 1.233,2.643 0.168,0.202 10 1 3.128,1.022 3.481,1.224 0.353,0.202 10 OT+

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the tester, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approximately 80°C (176°F)

·

With engine cold: Equal to ambient temperature


If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.

HINT:

When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.

When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the tester in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

If a circuit related to the ATF temperature sensor becomes open, P0713 is stored immediately (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored. It is not necessary to inspect the circuit when P0711 is stored.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)
C214326E01
2.019,1.306 1.82,1.745 false 2.087,1.087 2.341,1.745 false 1.583,1.783 1.911,1.950 0.329,0.167 10 OT+ 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 2.202,1.783 2.530,1.950 0.329,0.167 10 OT-

a.

Disconnect the C30 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (OT-) - 10 (OT+) Always 79 Ω to 156 kΩ
2 (OT-) - Body ground Always 10 kΩ or higher
10 (OT+) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at one of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


Resistance (Reference):
ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Text in Illustration
*a Component without harness connected
(Transmission Wire)


OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

REPAIR OR REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
U169974E02
1.219,2.156 0.719,2.729 false 1.344,2.146 1.729,2.729 false 0.073,0 0.271,0.167 0.198,0.167 10 false *a 0.875,0.396 1.177,0.552 0.302,0.156 10 false G69 0.313,2.781 1.021,3.01 0.708,0.229 10 false 25 (THO1) 1.469,2.781 1.979,3 0.51,0.219 10 false 23 (E2)

a.

Disconnect the G69 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-25 (THO1) - G69-23 (E2) Always 79 Ω to 156 kΩ
G69-25 (THO1) - Body ground Always 10 kΩ or higher
G69-23 (E2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR