Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0973  Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)  P0974  Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In the case of an open or short circuit, the TCM stops sending current to the circuit. For details, refer to the fail-safe chart (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0973 TCM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection logic).
·

Short in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

TCM


P0974 TCM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip detection logic).
·

Open in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

TCM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S1 is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S1 circuit.

When shift solenoid valve S1 is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve S1 circuit (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>FAIL-SAFE CHART).

WIRING DIAGRAM

C219218E01
5.741,0.971 6.141,1.161 0.400,0.190 10 S1 5.915,3.234 6.315,3.424 0.400,0.190 10 TCM 5.915,3.079 6.315,3.268 0.400,0.190 10 G69 2.499,0.852 2.691,1.042 0.192,0.190 10 S1 2.805,1.08 2.937,1.269 0.132,0.190 10 8 5.481,1.08 5.676,1.269 0.194,0.190 10 18 1.021,1.707 2.551,1.896 1.530,0.190 10 Shift Solenoid Valve S1 0.942,2.916 2.264,3.106 1.322,0.190 10 Transmission Wire 0.942,2.764 1.278,2.954 0.335,0.190 10 C30

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve S1 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S1 ON ON OFF OFF OFF


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
a.
C214326E04
1.221,1.087 0.967,1.745 false 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 0.84,1.783 1.076,1.950 0.236,0.167 10 S1

Disconnect the C30 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
U169979E02
0.917,2.073 0.656,2.802 false 0.073,0.052 0.271,0.219 0.198,0.167 10 false *a 0.854,0.385 1.156,0.542 0.302,0.156 10 false G69 0.375,2.833 0.875,3.01 0.5,0.177 10 false 18 (S1)

Disconnect the G69 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-18 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Rear view of wire harness connector
(to TCM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR