Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0781  1-2 Shift (1-2 Shift Valve)  


DESCRIPTION

The 1-2 shift valve performs shifting to 1st gear and other gears.

DTC Code DTC Detection Condition Trouble Area
P0781 Gear required by the TCM does not match the actual gear when driving (2-trip detection logic*1, 1-trip detection logic*2).
·

Valve body is blocked up or stuck (1-2 shift valve)

·

Shift solenoid valve SLT remains open or closed

·

Automatic transmission (clutch, brake, gear, etc.)



*1: w/ OBD

*2: w/o OBD


MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the position in which the spring is compressed.

The TCM commands gear shifts by turning the shift solenoid valves ON/OFF and controls the oil pressure applied to the valves in the valve body.

The TCM calculates the actual transmission gear by comparing the signals from the input speed sensor NT and the output speed sensor SP2. The TCM can detect mechanical problems in the shift solenoids, valve body and automatic transmission (clutch, brake, gear, etc.). If the TCM detects that the actual gear position and commanded gear position are different, it will illuminate the MIL and store the DTC.

PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0781)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P0781 is output A
P0781 and other DTCs are output B

HINT:

If any other codes besides P0781 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)
CAUTION:

This test should always be performed with at least 2 people.


NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.



c.

Warm up the engine.


d.

Enter the following menus: Powertrain / ECT / Active Test.


e.

According to the display on the tester, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>FAIL-SAFE CHART).


ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th up-shift must be performed with the accelerator pedal released.

·

The 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the TCM is shown in the Data List display on the intelligent tester.



OK:

Gear position changes in accordance with the tester command.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

OK

4.CLEAR DTC AND PERFORM RUNNING TEST

NG

4.CLEAR DTC AND PERFORM RUNNING TEST

OK

END

NG

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY