Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FE)
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260769 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)  P0717  Input Speed Sensor Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input turbine speed of the transmission. By comparing the input turbine speed signal (NT) with the output shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. DTC Detection Condition Trouble Area
P0717 All conditions are met for 5 seconds or more (1 trip detection logic):
(a) Park/neutral position switch D input signal is ON.
(b) Gear position is 2nd, 3rd, 4th, 5th or 6th.
(c) Transmission output shaft speed is 1000 rpm or more.
(d) The vehicle speed is 25 km/h (15.5 mph) or more.
(e) Transmission revolution sensor (NT) value is less than 300 rpm.
·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM


P07BF When the transmission revolution sensor (NT) input voltage is below 0.1 V for 4.5 seconds or more (1 trip detection logic).
·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM


P07C0 When the transmission revolution sensor (NT) input voltage is higher than 1.9 V for 4.5 seconds or more (1 trip detection logic).
·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM



MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the transmission input shaft speed. The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).

While the vehicle is operating in 2nd, 3rd, 4th, 5th or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 and the output shaft speed is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C311983E84
5.438,3.365 5.896,3.563 0.458,0.198 10 false ECM 5.135,1.146 5.75,1.344 0.615,0.198 10 false NTB 2.76,1.146 3.083,1.333 0.323,0.188 10 false NTB 2.74,2.271 3.083,2.448 0.344,0.177 10 false NTO 5.135,2.271 5.75,2.469 0.615,0.198 10 false NTO 1.208,3.115 3.667,3.333 2.458,0.219 10 false Transmission Revolution Sensor (NT) 1.219,2.948 1.677,3.146 0.458,0.198 10 false C148 5.417,3.208 5.875,3.406 0.458,0.198 10 false C155 4.875,2.271 5.188,2.469 0.313,0.198 10 false 19 4.875,1.146 5.188,1.344 0.313,0.198 10 false 29 3.125,2.271 3.438,2.469 0.313,0.198 10 false 1 3.115,1.146 3.427,1.344 0.313,0.198 10 false 2 5.76,0.979 6.073,1.177 0.313,0.198 10 false 12V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FE)>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test in Road Test and drive the vehicle for 5 seconds or more at 50 km/h (31 mph) or more (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 2TR-FE)>ROAD TEST).



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed


Data is displayed in increments of 50 rpm

HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List


e.

In accordance with the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed


Data is displayed in increments of 50 rpm
NT Sensor Voltage Transmission revolution sensor (NT) output voltage/
Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -

Result
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.

Remove the transmission revolution sensor (NT) (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL).


b.

Connect the battery to the sensor as shown in the illustration.

C297974E21
1.99,1.948 1.792,1.469 false 1.417,1.948 1.615,1.479 false 5.01,0.49 4.844,0.375 false 6.021,0.948 5.75,0.813 false 5.302,2.208 5.76,1.708 false 4.604,2.49 4.813,2.396 false 3.792,0.688 3.948,0.583 false 4.396,0.688 4.24,0.583 false 6.063,0.896 6.49,1.094 0.427,0.198 10 false *3 5.042,0.469 5.271,0.667 0.229,0.198 10 false *2 1.094,0.552 1.521,0.75 0.427,0.198 10 false *1 5.781,1.563 6.208,1.76 0.427,0.198 10 false *4 4.448,2.438 4.875,2.635 0.427,0.198 10 false *a 1.844,1.99 2.271,2.188 0.427,0.198 10 false NTO 4.427,0.615 5.271,0.813 0.844,0.198 10 false 1 (NTO) 3.271,0.615 4.115,0.813 0.844,0.198 10 false 2 (NTB) 1.24,1.99 1.667,2.188 0.427,0.198 10 false NTB

Text in Illustration
*1 Transmission Revolution Sensor (NT) *2 Ammeter
*3 Battery *4 Magnet
*a 5 mm (0.197 in.) or less - -


c.

Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
1 (NTO) - 2 (NTB) High signal 12 to 16 mA




OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
a.

Disconnect the C148 transmission revolution sensor (NT) connector.


b.

Disconnect the C155 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C148-2 (NTB) - C155-29 (NTB) Always Below 1 Ω
C148-1 (NTO) - C155-19 (NTO) Always Below 1 Ω
C148-2 (NTB) - Body ground Always 10 kΩ or higher
C148-1 (NTO) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR