Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260770 AUTOMATIC TRANSMISSION FLUID A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSMISSION FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C323946

Remove the drain plug and gasket from the automatic transmission assembly and drain the automatic transmission fluid. [*2]


c.

Temporarily install the gasket and drain plug to the automatic transmission assembly. [*3]

HINT:

Reuse the old gasket as the drain plug will be removed again.



d.
C323948

Remove the refill plug and O-ring from the automatic transmission assembly. [*4]


e.
C323944

Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly. [*5]


f.
C323940E03
1.396,0.917 1.042,1.833 1.042,1.833 0.875,1.833 true 1.531,3.74 1.281,4.396 1.281,4.396 1.125,4.396 true 0.927,4.313 1.083,4.49 0.156,0.177 10 false *b 0.677,1.74 0.833,1.917 0.156,0.177 10 false *a

Add automatic transmission fluid to the refill hole until it flows out of the overflow hole. [*6]

Text in Illustration
*a Refill Hole
*b Overflow Hole

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.




g.
C323942

Wait until the automatic transmission fluid flow slows and only drips come out. [*7]


h.
C323944

Using a 5 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transmission assembly. [*8]

HINT:

Reuse the old gasket as the overflow plug will be removed again.



i.

Add the amount of automatic transmission fluid specified for removal and installation of the automatic transmission oil pan sub-assembly to the refill hole. [*9]

Specified amount of fluid:
for 2TR-FE:

0.8 liters (0.8 US qts, 0.7 Imp. qts)

for 1GD-FTV, 1GR-FE:

2.4 liters (2.5 US qts, 2.1 Imp. qts)


HINT:

If the specified amount of automatic transmission fluid cannot be added, perform steps [*10] to [*15].



j.

Temporarily install the O-ring and refill plug to the automatic transmission assembly. [*10]

HINT:

Reuse the old O-ring as the refill plug will be removed again.



k.

Lower the vehicle. [*11]


l.

Start the engine. [*12]

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



m.

Slowly move the shift lever from P to S, and then back to P. [*13]


n.

Allow the engine to idle for 30 seconds to warm it up. [*14]


o.

Turn the ignition switch off. [*15]


p.

Repeat steps [*1] to [*15].


q.

Repeat steps [*1] to [*2].


r.

Install a new gasket and the drain plug to the automatic transmission assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


s.

Repeat steps [*4] to [*11].


Hide 5. ATF THERMAL DEGRADATION ESTIMATE RESET