Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SPEED SENSOR
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260771 SPEED SENSOR G

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  SPEED SENSOR  INSPECTION  


PROCEDURE

Hide 89413N 1.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

a.

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.

C297974E27
2.021,1.979 1.844,1.469 true 1.365,1.979 1.542,1.469 true 5.01,0.5 4.813,0.354 true 6.188,1.021 5.75,0.813 true 5.292,2.25 5.75,1.75 true 4.563,2.521 4.802,2.396 false 3.781,0.708 3.948,0.604 true 4.385,0.698 4.229,0.594 true 4.542,1.708 3.99,1.427 true 6.219,0.979 6.646,1.177 0.427,0.198 10 false *2 5.042,0.448 5.271,0.646 0.229,0.198 10 false *b 1.094,0.552 1.521,0.75 0.427,0.198 10 false *a 5.781,1.615 6.208,1.813 0.427,0.198 10 false *c 4.375,2.458 4.552,2.667 0.177,0.208 10 false *d 1.906,2.021 2.333,2.219 0.427,0.198 10 false NTO 4.438,0.625 5.281,0.823 0.844,0.198 10 false 1 (NTO) 3.26,0.667 3.781,0.896 0.521,0.229 10 false 2 (NTB) 1.208,2.01 1.635,2.208 0.427,0.198 10 false NTB 3.76,1.323 3.99,1.521 0.229,0.198 10 false *1

Text in Illustration
*1 Transmission Revolution Sensor (NT) *2 Battery
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Ammeter
*c Magnet *d 5 mm (0.197 in.) or less


b.

Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NT).


Hide 89413R 2.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)

a.

Connect the battery to the transmission revolution sensor (SP2) as shown in the illustration.

C297974E28
2.042,1.958 1.865,1.448 true 1.365,1.969 1.542,1.458 true 5.021,0.479 4.823,0.333 true 6.188,1.021 5.75,0.813 true 5.292,2.24 5.75,1.74 true 4.583,2.521 4.823,2.396 false 3.781,0.688 3.948,0.583 true 4.385,0.688 4.229,0.583 true 4.531,1.698 3.979,1.417 true 6.219,0.979 6.646,1.177 0.427,0.198 10 false *2 5.042,0.438 5.271,0.635 0.229,0.198 10 false *b 1.094,0.552 1.521,0.75 0.427,0.198 10 false *a 5.781,1.563 6.208,1.76 0.427,0.198 10 false *c 4.396,2.469 4.823,2.667 0.427,0.198 10 false *d 1.906,2.01 2.333,2.208 0.427,0.198 10 false SP2O 4.438,0.615 5.281,0.813 0.844,0.198 10 false 1 (SP2O) 3.177,0.615 4.021,0.813 0.844,0.198 10 false 2 (SP2B) 1.156,2.021 1.583,2.219 0.427,0.198 10 false SP2B 3.781,1.313 4.01,1.51 0.229,0.198 10 false *1

Text in Illustration
*1 Transmission Revolution Sensor (SP2) *2 Battery
*a Component without harness connected
(Transmission Revolution Sensor (SP2))
*b Ammeter
*c Magnet *d 5 mm (0.197 in.) or less


b.

Wave a magnetic object left and right in front of the transmission revolution sensor (SP2) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (SP2O) - 2 (SP2B) Low signal 4 to 8 mA
High signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (SP2).