Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260775 SHIFT LEVER G

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 85903 1.INSPECT SHIFT LOCK CONTROL ECU (w/o Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control ECU.


a.

Inspect wire harness:

i.

Disconnect the shift lock control ECU connector.


ii.
C271751E02
2.042,1.344 2.583,1.344 true 2.021,1.563 2.167,1.927 2.167,1.927 2.427,1.927 true 1.583,1.573 1.458,1.969 1.458,1.969 1.26,1.969 true 0.854,1.531 1.396,1.531 true 1.406,1.323 1.063,1.135 1.063,1.135 0.906,1.135 true 0.125,0.125 0.333,0.313 0.208,0.188 10 false *a 0.417,1.448 0.823,1.635 0.406,0.188 10 false KLS+ 0.729,1.031 0.875,1.219 0.146,0.188 10 false E 0.865,1.875 1.208,2.063 0.344,0.188 10 false ACC 2.49,1.833 2.708,2 0.219,0.167 10 false IG 2.646,1.25 2.99,1.438 0.344,0.188 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
6 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
8 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control ECU)

If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


If the result is not as specified, replace the shift lock control ECU.


c.

Inspect shift lock solenoid:

i.
C354123E01
0.938,1.677 1.156,1.677 1.156,1.677 1.229,1.208 true 1.229,1.875 1.479,1.875 1.479,1.875 1.573,1.208 true 2.479,1.688 2.24,1.688 2.24,1.688 2.156,1.219 true 2.24,1.885 1.99,1.885 1.99,1.885 1.885,1.208 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.479,1.594 0.906,1.771 0.427,0.177 10 false SLS+ 0.823,1.792 1.198,1.969 0.375,0.177 10 false SLS- 2.292,1.833 2.667,2.01 0.375,0.177 10 false E2 2.521,1.604 2.896,1.781 0.375,0.177 10 false P

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control ECU)

If the result is not as specified, replace the transmission floor shift assembly.

If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.



Hide 85903 2.INSPECT SHIFT LOCK CONTROL ECU (w/ Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control ECU.


a.

Inspect wire harness:

i.

Disconnect the shift lock control ECU connector.


ii.
C296591E03
2.219,1.521 2.781,1.521 true 1.625,1.177 0.719,0.469 0.719,0.469 0.604,0.469 true 2.198,1.188 2.688,0.885 2.688,0.885 2.792,0.885 true 2.844,0.802 3.135,0.979 0.292,0.177 10 false STP 2.833,1.396 3,1.573 0.167,0.177 10 false IG 0.417,0.396 0.573,0.573 0.156,0.177 10 false E 0.073,0.01 0.229,0.188 0.156,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
6 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
12 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control ECU)

If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω




b.

Inspect shift lock solenoid:

i.
C354123E01
0.938,1.677 1.156,1.677 1.156,1.677 1.229,1.208 true 1.229,1.875 1.479,1.875 1.479,1.875 1.573,1.208 true 2.479,1.688 2.24,1.688 2.24,1.688 2.156,1.219 true 2.24,1.885 1.99,1.885 1.99,1.885 1.885,1.208 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.479,1.594 0.906,1.771 0.427,0.177 10 false SLS+ 0.823,1.792 1.198,1.969 0.375,0.177 10 false SLS- 2.292,1.833 2.667,2.01 0.375,0.177 10 false E2 2.521,1.604 2.896,1.781 0.375,0.177 10 false P

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control ECU)

If the result is not as specified, replace the transmission floor shift assembly.

If the shift lock does not operate when the power source of the transmission floor shift assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the transmission floor shift assembly.



Hide 3.INSPECT TRANSMISSION CONTROL SWITCH

a.

Disconnect the transmission control switch connector.


b.
C203344E54
1.969,0.781 2.26,0.781 true 1.802,0.729 2,0.219 2,0.219 2.125,0.219 true 1.635,0.729 1.438,0.219 1.438,0.219 1.323,0.219 true 1.625,0.99 1.281,1.51 1.281,1.51 1.167,1.51 true 1.938,0.99 2.135,1.5 2.135,1.5 2.25,1.5 true 2.156,0.125 2.531,0.302 0.375,0.177 10 false SFTU 2.302,0.688 2.708,0.865 0.406,0.177 10 false SFTD 1.115,0.135 1.281,0.313 0.167,0.177 10 false IG 2.281,1.406 2.438,1.583 0.156,0.177 10 false E 1.01,1.427 1.167,1.604 0.156,0.177 10 false S 0.083,0.01 0.24,0.188 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever held in "+" Below 1 Ω
Shift lever not held in "+" 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever held in "-" Below 1 Ω
Shift lever not held in "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)

If the result is not as specified, replace the transmission floor shift assembly.