Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TORQUE CONVERTER AND DRIVE PLATE
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260777 TORQUE CONVERTER AND DRIVE PLATE G

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C151051

Press on the spline of the stator with a finger and rotate the spline. Check that the spline rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.

Text in Illustration
V100135

Difficult
V100136

Smooth

If necessary, clean the torque converter assembly and recheck the one-way clutch. Replace the torque converter assembly if the one-way clutch still fails the inspection.



b.
C197457E08
0.113,0.092 0.341,0.288 0.228,0.195 10 *a 1.627,3.234 1.854,3.382 0.228,0.148 10 *b

Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Text in Illustration
*a Sample showing maximum allowable amount of powder in ATF
*b Full Scale

·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF in petri dish, which has been taken from a torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

i.

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly and drain it before replacing the ATF.



d.
D025368E78
1.781,1.823 2.26,1.052 true 2.302,0.969 2.521,1.156 0.219,0.188 10 false *c 0.49,0.115 0.698,0.292 0.208,0.177 10 false *a 1.531,0.115 1.698,0.271 0.167,0.156 10 false *b

Prevent deformation of the torque converter and damage to the oil pump gear.

Text in Illustration
*a CORRECT
*b INCORRECT
*c Bottom is damaged

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and torque converter assembly.



Hide 2.INSPECT DRIVE PLATE

a.
C238929E01
1.675,0.338 1.803,0.493 0.128,0.155 10 1 1.253,1.045 1.381,1.200 0.128,0.155 10 2 1.818,1.958 1.946,2.113 0.128,0.155 10 3 2.674,1.932 2.802,2.087 0.128,0.155 10 4 2.881,1.213 3.009,1.368 0.128,0.155 10 5 2.443,0.525 2.571,0.680 0.128,0.155 10 6

Check the drive plate for damage.

Text in Illustration
V100144

Measurement Point


b.

Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

for 1GR-FE:

(See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION)

for 2TR-FE:

(See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION)


Hide 32111 3.INSPECT PUMP IMPELLER DRIVE PLATE

a.
C333264E01
1.84,0.403 1.996,0.585 0.156,0.181 10 1 1.517,1.054 1.673,1.235 0.156,0.181 10 2 2.549,0.558 2.705,0.739 0.156,0.181 10 6 2.979,1.228 3.135,1.410 0.156,0.181 10 5 2.757,1.873 2.913,2.054 0.156,0.181 10 4 2.014,1.862 2.170,2.043 0.156,0.181 10 3

Check the pump impeller drive plate for damage.

Text in Illustration
V100144

Measurement Point


b.

Set up a dial indicator and measure the runout at the 6 areas on the pump impeller drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum or the pump impeller drive plate is damaged, replace the pump impeller drive plate.

(See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION)