Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260781 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)>FAIL-SAFE CHART).

DTC No. DTC Detection Condition Trouble Area
P0778 An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL2 circuit while driving and shifting gears (SL2 output signal duty is more than 0% and less than 100% under normal conditions) (1 trip detection logic).
·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the ECM detects the problem and illuminates the MIL and stores the DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)

While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL2 circuit, the ECM determines there is a malfunction (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)>FAIL-SAFE CHART).

WIRING DIAGRAM

C358478E02
5.771,0.792 6.385,0.99 0.615,0.198 10 false 12 V 5.188,1.135 5.802,1.333 0.615,0.198 10 false SL2+ 4.906,1.135 5.521,1.333 0.615,0.198 10 false 31 3.927,1.135 4.542,1.333 0.615,0.198 10 false 15 3.469,1.135 4.083,1.333 0.615,0.198 10 false SL2+ 3.49,2.094 4.104,2.292 0.615,0.198 10 false SL2- 3.927,2.094 4.542,2.292 0.615,0.198 10 false 16 4.896,2.094 5.51,2.292 0.615,0.198 10 false 32 5.198,2.094 5.813,2.292 0.615,0.198 10 false SL2- 1.5,1.719 5.167,1.917 3.667,0.198 10 false Shift Solenoid Valve SL2 1.01,1.313 1.625,1.51 0.615,0.198 10 false 1 1.031,2.146 1.646,2.344 0.615,0.198 10 false 2 1.802,2.698 2.417,2.896 0.615,0.198 10 false C146 1.813,2.896 3.229,3.135 1.417,0.24 10 false Transmission Wire 5.604,3.063 6.219,3.26 0.615,0.198 10 false C35 5.615,3.26 6.229,3.458 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)>PRECAUTION).


HINT:
·

The following table shows normal operation of the shift solenoid valve SL2 when the shift lever is in D:

ECM commanded gear 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL2 OFF OFF OFF ON ON ON

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Perform the D Position Shift Test in Road Test.




PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a.
C319326E57
2.073,1.75 1.854,1.188 false 1.469,1.75 1.698,1.188 false 0.125,0.073 0.552,0.271 0.427,0.198 10 false *a 1.302,1.802 1.729,2 0.427,0.198 10 false SL2- 1.958,1.802 2.385,2 0.427,0.198 10 false SL2+

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (SL2+) - 16 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
15 (SL2+) - Body ground Always 10 kΩ or higher
16 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U170462E02
2.188,2.333 2.51,2.948 false 2.115,2.333 1.792,2.948 false 1.875,0.188 2.385,0.396 0.51,0.208 10 false C35 0.104,0.104 0.615,0.313 0.51,0.208 10 false *a 2.26,3 2.969,3.208 0.708,0.208 10 false 31 (SL2+) 1.427,3 2.135,3.208 0.708,0.208 10 false 32 (SL2-)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-31 (SL2+) - C35-32 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C35-31 (SL2+) - Body ground Always 10 kΩ or higher
C35-32 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL2
a.
C197715E54
1.74,0.99 2.208,0.365 false 1.479,0.99 1.052,0.365 false 1.76,2.948 2.208,2.354 false 1.51,2.948 1.052,2.354 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)

Remove shift solenoid valve SL2 (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SL2


OK

NG