Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260781 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd start mode is selected with the pattern select (2ND) switch, the ECM controls the solenoid valves and the transmission starts from 2nd gear.

In 2nd start mode, the system operates the throttle motor to control engine output to reduce skidding of the drive wheels and guarantee stable acceleration from rest, straight driving and turning stability.

When the shift lever is in D, the transmission automatically shifts up from 2nd to 6th as usual.

HINT:
·

The pattern select (2ND) switch is a momentary-type switch.

·

In order to cancel 2nd start mode, push the pattern select (2ND) switch again or turn the engine switch off.



WIRING DIAGRAM

C326150E27
6.323,1.083 6.844,1.281 0.521,0.198 10 false 12 V 5.885,2.99 6.219,3.188 0.333,0.198 10 false G55 5.896,3.177 6.25,3.375 0.354,0.198 10 false ECM 5.229,1.25 5.448,1.448 0.219,0.198 10 false 19 3.927,1.25 4.083,1.448 0.156,0.198 10 false 4 3.531,1.25 3.99,1.448 0.458,0.198 10 false 2ND 2.563,1.25 2.792,1.448 0.229,0.198 10 false E 2.365,1.25 2.521,1.448 0.156,0.198 10 false 1 5.51,1.25 6.125,1.448 0.615,0.198 10 false SNWI 2.542,2.146 3.844,2.583 1.302,0.438 10 false Pattern Select (2ND) Switch Assembly 2.531,1.958 3.104,2.156 0.573,0.198 10 false G159

PROCEDURE

1.INSPECT PATTERN SELECT (2ND) SWITCH ASSEMBLY
a.
C199167E25
2.208,1.792 1.979,1.281 false 1.25,1.792 1.479,1.281 false 0.104,0.104 0.875,0.302 0.771,0.198 10 false *1 2.198,1.813 2.667,2.01 0.469,0.198 10 false E 1.083,1.813 1.594,2.01 0.51,0.198 10 false 2ND

Remove the pattern select (2ND) switch assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (E) - 4 (2ND) Pattern select (2ND) switch pushed Below 1 Ω
1 (E) - 4 (2ND) Pattern select (2ND) switch not pushed 10 kΩ or higher


Text in Illustration
*1 Pattern Select (2ND) Switch Assembly



OK

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (2ND) SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)
a.
U148261E05
1.24,1.833 1.469,1.323 false 0.104,0.104 0.292,0.302 0.188,0.198 10 false *a 0.458,0.99 0.938,1.177 0.479,0.188 10 false G159 1.167,1.865 1.323,2.063 0.156,0.198 10 false E

Disconnect the pattern select (2ND) switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-1 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Pattern Select (2ND) Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)
a.
U170457E02
0.75,2.229 0.979,2.833 false 0.406,0.188 0.917,0.396 0.51,0.208 10 false G55 0.073,0.021 0.583,0.229 0.51,0.208 10 false *a 0.76,2.885 1.583,3.094 0.823,0.208 10 false 19 (SNWI)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G55-19 (SNWI) - Body ground Pattern select (2ND) switch pushed Below 1 Ω
G55-19 (SNWI) - Body ground Pattern select (2ND) switch not pushed 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR