Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to the system description for DTC P2714 (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>P2714).

DTC No. DTC Detection Condition Trouble Area
P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C358447E03
1.531,1.635 3.208,1.865 1.677,0.229 10 false Solenoid Valve SLT 1.531,2.875 3.208,3.104 1.677,0.229 10 false Transmission Wire 1.542,2.688 3.219,2.917 1.677,0.229 10 false C146 1.094,1.292 1.302,1.49 0.208,0.198 10 false 1 1.052,2.167 1.26,2.365 0.208,0.198 10 false 2 3.427,1.115 3.813,1.313 0.385,0.198 10 false SLT+ 3.448,2.094 3.865,2.323 0.417,0.229 10 false SLT- 3.927,1.115 4.313,1.313 0.385,0.198 10 false 13 3.917,2.094 4.302,2.292 0.385,0.198 10 false 14 4.896,2.083 5.281,2.281 0.385,0.198 10 false 15 4.875,1.135 5.26,1.333 0.385,0.198 10 false 14 5.813,0.792 6.229,1.021 0.417,0.229 10 false 12 V 5.594,3.063 6.104,3.25 0.51,0.188 10 false C152 5.604,3.25 6.083,3.458 0.479,0.208 10 false ECM 5.177,1.125 5.563,1.323 0.385,0.198 10 false SLT+ 5.188,2.083 5.604,2.313 0.417,0.229 10 false SLT-

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C319326E06
2.376,1.7 2.152,1.139 false 0.122,0.069 0.547,0.271 0.425,0.202 10 *a 1.556,1.748 1.982,1.950 0.425,0.202 10 SLT- 2.212,1.748 2.637,1.950 0.425,0.202 10 SLT+ 1.771,1.7 1.995,1.139 false

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLT+) - 14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLT+) - Body ground Always 10 kΩ or higher
14 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U170426E02
1.802,1.885 2.188,2.698 false 1.729,1.885 1.365,2.698 false 0.104,0.156 0.615,0.365 0.51,0.208 10 false *a 1.802,0.24 2.313,0.448 0.51,0.208 10 false C152 1.927,2.75 2.74,2.958 0.813,0.208 10 false 14 (SLT+) 1.01,2.75 1.823,2.958 0.813,0.208 10 false 15 (SLT-)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C152-14 (SLT+) - C152-15 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C152-14 (SLT+) - Body ground Always 10 kΩ or higher
C152-15 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C197715E22
1.75,0.979 2.208,0.365 false 1.49,0.979 1.052,0.365 false 1.76,2.948 2.208,2.354 false 1.51,2.948 1.052,2.354 false 0.073,0.042 0.385,0.24 0.313,0.198 10 false *1 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)

Remove shift solenoid valve SLT (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SLT


OK

NG