Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › 2015.06–2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2810  Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>FAIL-SAFE CHART)

DTC No. DTC Detection Condition Trouble Area
P2810 An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL4 circuit while driving and shifting gears (SL4 output signal duty is more than 0% and less than 100% under normal conditions) (1 trip detection logic).
·

Open or short in shift solenoid valve SL4 circuit

·

Shift solenoid valve SL4

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL4 circuit. The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any of the shift solenoid valve circuits, the ECM detects the problem and illuminates the MIL and stores the DTC. The ECM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)

While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL4 circuit, the ECM determines there is a malfunction (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>FAIL-SAFE CHART).

WIRING DIAGRAM

C358447E05
1.531,1.635 3.208,1.865 1.677,0.229 10 false Shift Solenoid Valve SL4 1.531,2.875 3.208,3.104 1.677,0.229 10 false Transmission Wire 1.542,2.688 3.219,2.917 1.677,0.229 10 false C146 1.063,1.292 1.271,1.49 0.208,0.198 10 false 1 1.063,2.167 1.271,2.365 0.208,0.198 10 false 2 3.49,2.094 3.875,2.292 0.385,0.198 10 false SL4- 3.479,1.135 3.896,1.365 0.417,0.229 10 false SL4+ 4.958,1.115 5.344,1.313 0.385,0.198 10 false 9 3.917,2.104 4.302,2.302 0.385,0.198 10 false 24 3.927,1.115 4.313,1.313 0.385,0.198 10 false 23 4.958,2.083 5.344,2.281 0.385,0.198 10 false 8 5.188,2.115 5.573,2.313 0.385,0.198 10 false SL4- 5.188,1.135 5.604,1.365 0.417,0.229 10 false SL4+ 5.813,0.792 6.229,1.021 0.417,0.229 10 false 12 V 5.594,3.063 6.104,3.25 0.51,0.188 10 false C152 5.604,3.25 6.083,3.458 0.479,0.208 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>PRECAUTION).


HINT:
·

The following table shows normal operation of the shift solenoid valve SL4 when the shift lever is in D:

ECM commanded gear 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL4 OFF OFF ON OFF ON OFF

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.




PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL4)
a.
C319326E09
2.376,1.7 2.152,1.334 false 0.122,0.069 0.547,0.271 0.425,0.202 10 *a 1.556,1.748 1.982,1.950 0.425,0.202 10 SL4- 2.212,1.748 2.637,1.950 0.425,0.202 10 SL4+ 1.771,1.7 1.995,1.334 false

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
23 (SL4+) - 24 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
23 (SL4+) - Body ground Always 10 kΩ or higher
24 (SL4-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL4
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U170429E02
2.208,1.896 2.583,2.698 false 2.135,1.885 1.76,2.698 false 0.125,0.083 0.635,0.292 0.51,0.208 10 false *a 1.813,0.24 2.323,0.448 0.51,0.208 10 false C152 2.313,2.75 3.125,2.958 0.813,0.208 10 false 8 (SL4-) 1.396,2.75 2.208,2.958 0.813,0.208 10 false 9 (SL4+)

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C152-9 (SL4+) - C152-8 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
C152-9 (SL4+) - Body ground Always 10 kΩ or higher
C152-8 (SL4-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL4
a.
C197715E22
1.75,0.979 2.208,0.365 false 1.49,0.979 1.052,0.365 false 1.76,2.948 2.208,2.354 false 1.51,2.948 1.052,2.354 false 0.073,0.042 0.385,0.24 0.313,0.198 10 false *1 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.156,4.125 0.229,0.198 10 false (+) 1.167,3.927 1.396,4.125 0.229,0.198 10 false (-)

Remove shift solenoid valve SL4 (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SL4


OK

NG