Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER (for 1GD-FTV)
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260783 OIL COOLER(for 1GD-FTV) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 32907C 1.INSTALL OIL COOLER TUBE SUB-ASSEMBLY

a.
C332139

Install the oil cooler tube sub-assembly to the fan shroud with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Make contact with the terminal stopper.



Hide 2.INSTALL OIL COOLER HOSE

NOTICE:
·

When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.

·

Make sure to install the clips so that the spool fitting is not overlapped.



a.

Install the No. 1 transmission oil cooler hose to the radiator and oil cooler tube sub-assembly, and slide the 2 clips to secure them.

C332183E02
3.656,1.677 4.229,1.552 4.229,1.552 4.313,1.552 true 5.031,2.156 5.135,2.51 5.135,2.51 5.219,2.51 true 5.25,2.146 5.302,2.323 5.302,2.323 5.385,2.323 true 4.354,1.458 4.51,1.635 0.156,0.177 10 false *c 5.26,2.406 5.417,2.583 0.156,0.177 10 false *c 5.406,2.24 5.563,2.417 0.156,0.177 10 false *1 5.833,1.188 5.99,1.365 0.156,0.177 10 false *d 2.208,2.167 2.365,2.344 0.156,0.177 10 false *d 2.24,1.104 2.396,1.281 0.156,0.177 10 false *d 0.927,1.813 1.083,1.99 0.156,0.177 10 false *b 1.656,0.74 1.813,0.917 0.156,0.177 10 false *a 5.323,0.823 5.479,1 0.156,0.177 10 false *a

Text in Illustration
*1 No. 1 Flexible Hose Clamp - -
*a RH Side *b LH Side
*c Paint Mark *d 2 to 7 mm (0.0788 to 0.2755 in.)


b.

Attach the clamp.


c.

Install the No. 1 oil cooler inlet hose to the radiator, and slide the clip to secure it.


d.

Install the No. 1 oil cooler outlet hose to the oil cooler tube sub-assembly, and slide the clip to secure it.


e.

Then pass the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose through the No. 1 flexible hose clamp and close the No. 1 flexible hose clamp.


Hide 32921 3.INSTALL OIL COOLER INLET TUBE NO. 1 AND NO . 1 OIL COOLER OUTLET TUBE

NOTICE:
·

When disconnecting the hoses from the tube, support the tube by hand and be careful to prevent the tube from being deformed.

·

Make sure to install the clips so that the spool fitting is not overlapped.



a.

Install the 2 oil cooler tube clamps to the and engine assembly with the 2 bolts.

Torque:
for Bolt A : 14 N*m (143 kgf*cm, 10 ft.*lbf)
for Bolt B : 51 N*m (520 kgf*cm, 38 ft.*lbf)

U170488E02
1.99,0.896 1.885,1.167 1.885,1.167 1.792,1.167 true 5.708,2.135 5.625,2.344 5.625,2.344 5.552,2.344 true 4.656,1.063 4.75,1.354 4.75,1.354 4.823,1.354 true 1.615,1.083 1.771,1.26 0.156,0.177 10 false *1 4.865,1.271 5.021,1.448 0.156,0.177 10 true *2 5.354,2.26 5.51,2.438 0.156,0.177 10 false *2 5.177,1.563 5.313,1.719 0.135,0.156 10 false A 4.146,0.5 4.281,0.656 0.135,0.156 10 false B

Text in Illustration
*1 Flexible Hose Clamp *2 Oil Cooler Tube Clamp


b.

Connect the ends of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube to the automatic transmission assembly by hand.


c.

Close the 2 oil cooler tube clamps and install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.
C333103E02
0.865,0.25 1.021,0.427 0.156,0.177 10 false *a 1.063,2.094 1.219,2.271 0.156,0.177 10 false *b

Connect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, and slide the 2 clips to secure them.

Text in Illustration
*a Upper Side
*b 2 to 7 mm (0.0788 to 0.2755 in.)


e.
C324535E05
1.875,1.333 2.031,1.51 0.156,0.177 10 true *a

Using a 17 mm union nut wrench, tighten the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

Torque:
Specified tightening torque : 34 N*m (350 kgf*cm, 25 ft.*lbf)

Text in Illustration
*a Torque Wrench Fulcrum Length

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 29 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 51405A 7.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY