Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER (for LHD)
RM27T0E _52 Drivetrain _053699 CLUTCH _0260794 CLUTCH MASTER CYLINDER(for LHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 31410 1.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.

Install the clutch master cylinder with the 2 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


b.
U170061E01
0.423,1.908 0.624,2.085 0.201,0.177 10 *1

Apply MP grease to the contact surfaces of the pin and clevis bush.

Text in Illustration
*1 MP grease


c.

Connect the clevis to the clutch pedal with the pin.


d.

Install a new clip to the pin.


e.

Install the clutch start switch with the nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


f.

Using a union nut wrench, connect the flexible tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



g.
C215420E01
0.903,2.348 1.104,2.524 0.201,0.177 10 *1 0.685,2.625 0.814,2.437 false 0.809,2.44 0.883,2.44 false

Connect the clutch reservoir hose.

Text in Illustration
*1 Paint Mark
V100135

Top
V100136

Left
V100137

Rear

HINT:
·

Make sure the paint mark of the clutch reservoir hose is facing upward.

·

Make sure the direction of the clamp is as shown in the illustration.




Hide 2.INSTALL CLUTCH PEDAL WITH CLUTCH MASTER CYLINDER

a.

Install the clutch pedal with clutch master cylinder to the vehicle with the 2 nuts and bolt.

Torque:
for nut : 16 N*m (163 kgf*cm, 12 ft.*lbf)
for bolt : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

w/ Cruise Control:

Connect the clutch switch connector.


c.

Connect the clutch start switch connector.


Hide 82731 3.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY

a.

Install the driver side junction block (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


Hide 31481 4.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.

Using a union nut wrench, connect the flexible hose tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 31434 5.CONNECT CLUTCH RESERVOIR TUBE

a.
C217683

Connect the clutch reservoir tube.

Text in Illustration
V100135

Top
V100136

Left

HINT:

Make sure the direction of the clamp is as shown in the illustration.



Hide 6.FILL RESERVOIR WITH BRAKE FLUID

Hide 8.CHECK FLUID LEVEL IN RESERVOIR

Hide 9.CHECK FOR BRAKE FLUID LEAK FROM CLUTCH LINE

Hide 31301 10.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY