Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 1GR-FE)
RM27T0E _52 Drivetrain _053699 CLUTCH _0260801 CLUTCH UNIT(for 1GR-FE) A

CLUTCH  CLUTCH UNIT(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C215507E01
1.127,2.656 1.512,2.868 0.385,0.211 10 SST 2.082,1.595 1.308,2.468 false 1.308,2.468 1.308,2.613 false

Insert SST into the clutch disc, and then install SST and the clutch disc together to the flywheel.

SST
09301-00110  

Text in Illustration
V100135

Flywheel Side

NOTICE:

Be sure to install the clutch disc so that it is facing in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C215508E01
0.596,0.441 0.825,0.644 0.229,0.203 10 *a 0.826,0.145 1.156,0.304 0.330,0.159 10 1, 4 2.89,0.776 3.025,0.932 0.135,0.156 10 2 1.194,1.953 1.329,2.109 0.135,0.156 10 3 2.579,0.054 2.714,0.209 0.135,0.156 10 5 2.105,1.914 2.240,2.070 0.135,0.156 10 6 0.678,1.029 0.813,1.185 0.135,0.156 10 7 3.034,1.032 3.335,1.244 0.302,0.211 10 SST 2.498,1.277 2.764,1.117 false 2.764,1.117 3.001,1.117 false 1.166,0.896 0.81,0.552 false 0.81,0.552 1.269,0.926 false

a.

Align the matchmark on the clutch cover with the one on the flywheel.

Text in Illustration
*a Matchmark


b.

Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00110  

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, and right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C215509E01
2.465,2.344 2.843,2.583 0.378,0.239 10 SST 1.788,3.405 2.187,2.428 false 2.187,2.428 2.417,2.428 false

a.

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

SST
09333-00013  

Maximum misalignment:

0.5 mm (0.0196 in.)


If the misalignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
U169896E01
0.462,1.936 0.916,2.112 0.454,0.176 10 *1

Apply release hub grease to the release fork, release bearing, push rod contact point and pivot points shown in the illustration.

Grease:

Toyota Genuine Release Hub Grease or equivalent


Text in Illustration
*1 Release hub grease


b.
U170076E01
0.532,1.868 0.757,2.066 0.225,0.198 10 *1

Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Text in Illustration
*1 Clutch spline grease


c.

Install the clutch release bearing to the clutch release fork with the clip.


d.

Install the release fork support to the transmission unit.

Torque:
47 N*m (480 kgf*cm, 35 ft.*lbf)


e.

Install the clutch release fork with the clutch release bearing to the transmission unit.

HINT:

After installation, move the fork back and forth to check that the release bearing slides smoothly.



Hide 5.INSTALL MANUAL TRANSMISSION ASSEMBLY