Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 5L-E)
RM27T0E _52 Drivetrain _053699 CLUTCH _0260803 CLUTCH UNIT(for 5L-E) A

CLUTCH  CLUTCH UNIT(for 5L-E)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C215524E01
2.516,1.454 2.904,1.675 0.387,0.221 10 SST 2.15,1.535 2.459,1.535 false

Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel to install the clutch disc.

SST
09301-00110  

Text in Illustration
V100135

Flywheel Side

NOTICE:

Be sure to install the clutch disc so that it is facing in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C215525E03
0.635,1.313 0.292,1.146 true 0.292,1.146 0.771,1.26 true 2.24,0.854 2.656,1.177 false 2.656,1.177 2.802,1.177 false 2.865,1.094 3.188,1.24 0.323,0.146 10 false SST 2.375,1.198 2.5,1.344 0.125,0.146 10 false 2 2.042,0.083 2.167,0.229 0.125,0.146 10 false 5 0.563,1.896 0.688,2.042 0.125,0.146 10 false 3 2.031,1.948 2.156,2.094 0.125,0.146 10 false 6 0.177,0.104 0.594,0.281 0.417,0.177 10 false 1, 4 0.417,0.667 0.563,0.854 0.146,0.188 10 true 7 0.094,1.042 0.302,1.26 0.208,0.219 10 false *a

a.

Align the matchmarks on the clutch cover and flywheel.

Text in Illustration
*a Matchmark


b.

Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

SST
09301-00110  

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Move SST up and down, and right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.



Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C215526E01
2.155,2.367 2.512,2.558 0.357,0.191 10 SST 1.795,3.439 1.981,2.447 false 1.981,2.447 2.118,2.447 false

a.

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

SST
09333-00013  

Maximum non-alignment:

0.5 mm (0.0196 in.)


If the alignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.



Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission unit.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 31230 5.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

U170083E01
0.551,2.395 0.832,2.578 0.281,0.184 10 *a

a.

Apply release hub grease to the clutch release bearing, and then install it to the clutch release fork with the clip.

Grease:

Toyota Genuine Release Hub Grease or equivalent


Text in Illustration
*a Release hub grease


Hide 31204 6.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.

Install the clutch release fork.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



b.
U170080E02
0.438,1.917 0.688,2.104 0.25,0.188 10 true *a

Apply clutch spline grease to the spline of the input shaft.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Text in Illustration
*a Clutch spline grease


Hide 31126 7.INSTALL CLUTCH RELEASE FORK BOOT

Hide 33030 8.INSTALL MANUAL TRANSMISSION ASSEMBLY