33333A
1.INSTALL 3RD GEAR NEEDLE ROLLER BEARING
Coat the needle roller bearing with gear oil and install it to the output shaft.
33333
2.INSTALL 3RD GEAR
Coat the 3rd gear with gear oil and install it to the output shaft.
33367
3.INSTALL NO. 1 SYNCHRONIZER RING
Coat the No. 1 synchronizer ring with gear oil and install it to the 3rd gear.
33362
4.INSTALL NO. 2 TRANSMISSION CLUTCH HUB
Coat the hub sleeve with gear oil and install it to the clutch hub.
|
Front |
Be sure to install the hub sleeve to the clutch hub in the correct direction.
Install the 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.
Do not set both openings of the shifting key springs in the same position.
Using SST and a press, install the No. 2 clutch hub to the output shaft.
Select a clutch hub shaft snap ring that will allow minimal axial play.
0.10 mm (0.00394 in.) or less
| Mark | Thickness |
|---|---|
| C-1 | 1.75 to 1.80 mm (0.0689 to 0.0709 in.) |
| D | 1.80 to 1.85 mm (0.0709 to 0.0728 in.) |
| D-1 | 1.85 to 1.90 mm (0.0728 to 0.0748 in.) |
| E | 1.90 to 1.95 mm (0.0748 to 0.0768 in.) |
| E-1 | 1.95 to 2.00 mm (0.0768 to 0.0787 in.) |
| F | 2.00 to 2.05 mm (0.0787 to 0.0807 in.) |
| F-1 | 2.05 to 2.10 mm (0.0807 to 0.0827 in.) |
Using a snap ring expander, install the snap ring.
33333
5.INSPECT 3RD GEAR THRUST CLEARANCE
33332B
6.INSTALL 2ND GEAR NEEDLE ROLLER BEARING
Coat the needle roller bearing with gear oil and install it to the output shaft.
33332
7.INSTALL 2ND GEAR
Coat the 2nd gear with gear oil and install it to the output shaft.
33368
8.INSTALL NO. 2 SYNCHRONIZER RING (for 2nd Gear)
Coat the No. 2 synchronizer ring with gear oil and install it to the 2nd gear.
33361
9.INSTALL NO. 1 TRANSMISSION CLUTCH HUB
Coat the reverse gear with gear oil and install it to the clutch hub.
|
Front |
Be sure to install the reverse gear to the clutch hub in the correct direction.
Install the 3 synchromesh shifting keys to the clutch hub with the 2 synchromesh shifting key springs.
Do not set both openings of the shifting key springs in the same position.
Using SST and a press, install the clutch hub to the output shaft.
33367
10.INSTALL NO. 1 SYNCHRONIZER RING (for 1st Gear)
Coat the synchronizer ring with gear oil and install it to the No. 1 clutch hub.
33355A
11.INSTALL 1ST GEAR BEARING INNER RACE LOCK BALL
Coat the lock ball with gear oil and install it to the output shaft.
33355
12.INSTALL 1ST GEAR BEARING INNER RACE
Coat the needle roller bearing with gear oil.
Install the inner race and needle roller bearing to the 1st gear.
| *1 | 1st Gear Bearing Inner Race |
| *2 | 1st Gear Needle Roller Bearing |
| *3 | 1st Gear |
33335
13.INSTALL 1ST GEAR
Coat the 1st gear with gear oil and install it to the output shaft.
33321V
14.INSTALL OUTPUT SHAFT CENTER BEARING
Using SST and a press, install the center bearing to the output shaft.
33335
15.INSPECT 1ST GEAR THRUST CLEARANCE
33336
16.INSTALL 5TH GEAR
Using SST and a press, install the 5th gear to the output shaft.
Select a snap ring that will allow minimal axial play.
0.10 mm (0.00394 in.) or less
| Mark | Thickness |
|---|---|
| A | 2.67 to 2.72 mm (0.1052 to 0.1070 in.) |
| B | 2.73 to 2.78 mm (0.1075 to 0.1094 in.) |
| C | 2.79 to 2.84 mm (0.1099 to 0.1118 in.) |
| D | 2.85 to 2.90 mm (0.1123 to 0.1141 in.) |
| E | 2.91 to 2.96 mm (0.1146 to 0.1165 in.) |
| F | 2.97 to 3.02 mm (0.1170 to 0.1188 in.) |
| G | 3.03 to 3.08 mm (0.1193 to 0.1212 in.) |
| H | 3.09 to 3.14 mm (0.1217 to 0.1236 in.) |
| J | 3.15 to 3.20 mm (0.1241 to 0.1259 in.) |
| K | 3.21 to 3.26 mm (0.1264 to 0.1283 in.) |
| L | 3.27 to 3.32 mm (0.1288 to 0.1307 in.) |
Using a brass bar and hammer, tap on the snap ring.
33336
17.INSPECT 5TH GEAR THRUST CLEARANCE
33333
18.INSPECT 3RD GEAR THRUST CLEARANCE
33332
19.INSPECT 2ND GEAR THRUST CLEARANCE
33335
20.INSPECT 1ST GEAR THRUST CLEARANCE
33333
21.INSPECT 3RD GEAR RADIAL CLEARANCE
33332
22.INSPECT 2ND GEAR RADIAL CLEARANCE
33335
23.INSPECT 1ST GEAR RADIAL CLEARANCE